Valor 2200KN Installation Manual Download Page 10

10

WARNING

Some materials or items, although safe, 

may discolor, shrink, warp, crack, peel 

and so on because of the heat produced 

by the fireplace. Avoid placing candles, 

paintings, photos, and other items 

sensitive to heat around the fireplace.

WARNING

HOT WALL SURFACES! The walls directly 

above the fireplace are constructed of non-

combustible materials and, although safe, it 

may reach temperatures in excess of 

200 

°

F depending on choice of materials. Do 

not touch! Finish the walls using materials 

suitable for these temperatures.

WARNING

Ensure weight of wall above is 

NOT carried by the appliance.

2200K heater

Framing—See Framing 

pages 15 - 16

1/2” thick non-combustible 

cement board 

required

 above 

and on both sides of 

fi

 replace 

opening–

NOT supplied

1/2” thick non-combustible 

cement board 

required

 above 

and on both sides of 

fi

 replace 

opening–

NOT supplied

Wall 

fi

 nish below opening

Combustible material up to 

1-1/4” thick allowed below 

opening. Combustible 

projections must otherwise be 

kept min. 4” below opening.

HeatShift front outlet

HeatShift sides outlet

Remote 

Control 

Handset 

Wall Holder

Wall Finish abo

ve ope

nin

g

Combustible wall 

fi

 nish up to 

3/4” thick allowed above opening 

overtop of 1/2” cement board. 

Combustible projections must 

otherwise conform to allowable 

mantel projections

—se

e p

p

p

p

age

g

g

g

 11.

Remote Battery 

and Wall Switch Kit 

(required) 

(35-foot wire 

length) (supplied)

Combustible Material Allowed Beneath Fireplace. 

When the appliance is installed directly on carpeting, 

tile or other combustible material other than wood 

fl

 ooring, the appliance shall be installed on a metal 

or wood panel extending the full width and recessed 

depth of the appliance.

Vent collar supplied as 5 x 8” outlet, 

fi

 eld convertible to 4 x 6-5/8” 

outlet (adapter supplied). Note - Vertical rise required in vent system 

when adapting to 4 x 6-5/8” venting

HeatShift Plenum (front or sides) or Duct 

Termination Plates (top) 

mandatory! 

HeatShift 

system supplied separately—see “Appendix D - 

HeatShift System” on page 72

HeatShift ducts (4)

Planning

Overview

Summary of Contents for 2200KN





























































































Reviews: