manualshive.com logo in svg

Valet 551R, Installation Manual

The Valet 551R automatic car park assist system brings convenience to your parking routine. Ensure a hassle-free installation with our comprehensive Installation Manual, available for free download at manualshive.com. This manual provides step-by-step instructions and invaluable insights for optimal usage of this remarkable product.

Share
Download
background image

2

© 2000 Directed Electronics, Inc. Vista, CA

table of contents

Bitwriter™, Code Hopping™, DEI®, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn
Routine™, Nite-Lite®, Nuisance Prevention Circuitry®, NPC®, Revenger®, Silent Mode™, Soft Chirp®,
Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn Away® are all Trademarks or Registered
Trademarks of Directed Electronics, Inc.

What Is Included

. . . . . . . . . . . . . . . . . . . . . 3

Warning! Safety First

. . . . . . . . . . . . . . . . . . 4

Installation Points to Remember

. . . . . . . . . . 5

Finding The Wires You Need

. . . . . . . . . . . . . . 6

Obtaining Constant 12V . . . . . . . . . . . . . . . 6
Finding the Starter Wire. . . . . . . . . . . . . . . 6
Finding the 12V Switched Ignition Wire . . . . 7
Finding the Accessory Wire . . . . . . . . . . . . . 7
Finding a (+) Parking Light Wire . . . . . . . . . 7
Finding the Tachometer Wire. . . . . . . . . . . . 8
Finding the Wait-To-Start Bulb
Wire For Diesels  . . . . . . . . . . . . . . . . . . . 9

Wiring Diagrams

. . . . . . . . . . . . . . . . . . . . . . 9

Primary Harness (H1) Wiring Diagram . . . . . . 9
Remote Start Ribbon Harness Wiring Diagram . 10
Heavy Gauge Relay Satellite Wiring Diagram . 10
Remote Start Harness (H2) Wiring Diagram. . 10

Wire Connection Guides

. . . . . . . . . . . . . . . . 11

Primary Harness (H1), 8-Pin Connector . . . . 11
Relay Satellite Key Switch Interface . . . . . . 14
Remote Start Harness (H2), 6-Pin Connector . . 15

Neutral Safety Switch Interface

. . . . . . . . . . 16

GM Trucks, SUVs and Column-Shifting 
Passenger Cars . . . . . . . . . . . . . . . . . . . . 18
Pre-1996 Dodge Dakota Pickups with
2.5 Liter Motors . . . . . . . . . . . . . . . . . . . 18

Bypassing GM Vehicle Anti-Theft Systems

. . . . 19

1995 and Newer Vehicle Anti-Theft Systems
(Immobilizers)

. . . . . . . . . . . . . . . . . . . . . . 20

Passlock I and Passlock II (PL-1 and PL-2). . 20
Passkey III (PK-3), Transponder-Based Systems . 20

Optional Anti-Grind Relay

. . . . . . . . . . . . . . 21

Door Lock Wiring Guide

. . . . . . . . . . . . . . . . 22

Positive-Triggered, Relay Driven
Systems (Type A) . . . . . . . . . . . . . . . . . . 22
Negative-Triggered, Relay Driven
Systems (Type B) . . . . . . . . . . . . . . . . . . 23
Reversing Polarity System (Type C) . . . . . . . 24
Actuators (Type D) . . . . . . . . . . . . . . . . . 25
Electrically Activated Vacuum (Type E) . . . . 26
One-Wire System, (Type F) . . . . . . . . . . . . 26
Type G: Positive (+) Multiplex . . . . . . . . . . 27
Type H: Negative (-) Multiplex . . . . . . . . . . 28

Internal Programming Jumper

. . . . . . . . . . . 29

Digital Tach Threshold On/Off . . . . . . . . . . 29

Plug-in Program Switch

. . . . . . . . . . . . . . . . 30

Transmitter/Receiver Learn Routine

. . . . . . . . 30

Tach Learning

. . . . . . . . . . . . . . . . . . . . . . . 31

Operating-Settings Learn Routine

. . . . . . . . . 32

Features Menu

. . . . . . . . . . . . . . . . . . . . . . 33

Feature Descriptions

. . . . . . . . . . . . . . . . . . 33

Shutdown Diagnostics

. . . . . . . . . . . . . . . . . 35

Timer Mode

. . . . . . . . . . . . . . . . . . . . . . . . 36

Safety Check

. . . . . . . . . . . . . . . . . . . . . . . 37

Troubleshooting

. . . . . . . . . . . . . . . . . . . . . 38

Wiring Quick Reference Guide

. . . . . . . . . . . 40

Summary of Contents for 551R









































Reviews:

No comments

Related manuals for 551R

Hama A40 Operating Instructions Manual preview
A40
Brand: Hama Pages: 10
iHome iA5 Instruction Manual preview
iA5
Brand: iHome Pages: 18
Clifford IntelliGuard 8000 Complete Owner'S Manual preview
IntelliGuard 8000
Brand: Clifford Pages: 12
Clifford ACE 4000 Complete Owner'S Manual preview
ACE 4000
Brand: Clifford Pages: 9
K-9 K9-Mundial-3 Quick Start Manual preview
K9-Mundial-3
Brand: K-9 Pages: 2
Kidde Fyrnetics 423/9HIR Installer'S Manual preview
Fyrnetics 423/9HIR
Brand: Kidde Pages: 10
RHINO ENHANCER Operation Instructions Manual preview
ENHANCER
Brand: RHINO Pages: 6
Pandora DXL 1930L Manual preview
DXL 1930L
Brand: Pandora Pages: 21
TSS DS500 CAN U User& Installer'S Manual preview
DS500 CAN U
Brand: TSS Pages: 23
CrimeStopper SP-100 Installation And Operating Instructions Manual preview
SP-100
Brand: CrimeStopper Pages: 16
CrimeStopper CS-2002 Installation And Operating Instructions Manual preview
CS-2002
Brand: CrimeStopper Pages: 20
Crime Guard 328i3 Operation Manual preview
328i3
Brand: Crime Guard Pages: 82
Apollo AlarmSense Manual preview
AlarmSense
Brand: Apollo Pages: 2
Datexx iTALK DF-83 User Manual preview
iTALK DF-83
Brand: Datexx Pages: 1
Fire-Lite Alarms BG-12 Manual preview
BG-12
Brand: Fire-Lite Alarms Pages: 2
IKEA FNURRA Manual preview
FNURRA
Brand: IKEA Pages: 44
Hama RC 40 Operating Instructions Manual preview
RC 40
Brand: Hama Pages: 13
Hama 106941 Operating Instructions Manual preview
106941
Brand: Hama Pages: 16

Brands by name

Popular brands

Load more brands