background image

Valentine One

®

 Generation 2

QUICK START GUIDE

Controls and Functions


Volume –

Press-and-hold to 

raise or lower Initial 

Volume.  Sound 

level 0-9 indicated 

in display during 

adjustment.

  

Control Button

 

Power on - Tap Control Button

 

Power off -  Press-and-hold 

Control Button until 

display goes dark 

(4.75 seconds)

Changing modes - Press-and-hold  

 

 

 Control Button for   

 

 1.5 seconds

 

Muting -  Tap Control Button  

during an alert

Band Identification

NOTE:  In the case of 

multiple bogeys on different 

bands, a blinking icon will 

indicate the most urgent 

threat.

Radar-strength 

Indicator

More blocks glow as  

radar gets stronger.

Bluetooth

®

  

icon

Illuminated when  

connected.

Radar Locator

Radar ahead

Radar beside Radar behind

NOTE:  In the case of multiple bogeys 

from different directions, an arrow 

will glow for each direction.  The 

most urgent threat will be indicated 

by a blinking arrow.  The audio 

warning will correspond to the 

blinking arrow.

Rear Radar 

Antenna

Needs unobstructed 

view behind.

Rear Laser Sensor

Needs unobstructed  

view behind.

Mute icon

Illuminated when volume is muted.

Front Antenna, Radar and Laser

Needs unobstructed view ahead.

Power In

Speaker

Headphone

Jack

WARNING: USE THIS PRODUCT ONLY IN ACCORDANCE 
WITH ITS END USER LICENSE AGREEMENT.  WATCHING 
THE SCREEN WHILE YOUR VEHICLE IS IN MOTION MAY BE 
DANGEROUS.  DRIVE SAFELY AND OBEY ALL TRAFFIC LAWS.

USE OF V1connection, the app IS SUBJECT TO THE END USER 
LICENSE AGREEMENT AS APPEARING AT   
http://www.valentine1.com/v1info/v1connection/
v1connectioneula.pdf
.

Hereby, Valentine Research, Inc., declares that this radar detector 
is in compliance with the essential requirements and other 
relevant provisions of Directive 2014/53/EU.

Refer to http://www.valentine1.com/standards

 

for the Document 

of Conformity.

This device complies with Part 15 of the FCC Rules.  Operation is 
subject to the following two conditions: 
1)   this device may not cause harmful interference, and 
2)  this device must accept any interference  received, including 

interference that may cause undesired operation.

NOTE:  The manufacturer is not responsible for any radio or 
TV interference caused by unauthorized modifications to this 
equipment.  Such modifications could void the user’s authority to 
operate the equipment.

V1connection is a trademark of Valentine Research, Inc.  |     
SAVVY is a registered trademark of Valentine Research, Inc. 
iPhone, iPad and iPod touch are registered trademarks of  
Apple Inc.  |  Android is a trademark of Google Inc.

Bluetooth is a registered trademark of 
Bluetooth SIG, Inc. 
QDID:  D038345 and D037292     

Contains FCC ID:  QJAG2   
Contains IC:  109191A-G2   

Le présent appareil est conforme aux CNR d’Industrie Canada 
applicables aux appareils radio exempts de licence. L’exploitation 
est autorisée aux deux conditions suivantes: 
1) l’appareil ne doit pas produire de brouillage, et 

2)  l’utilisateur de l’appareil doit accepter tout brouillage 

radioélectrique subi, même si le brouillage est susceptible  

d’en compromettre le fonctionnement.

Under Industry Canada regulations, this radio transmitter may 
only operate using an antenna of a type and maximum (or lesser) 
gain approved for the transmitter by Industry Canada.  To reduce 
potential radio interference to other users, the antenna type and 
its gain should be so chosen that the equivalent isotropically 
radiated power (e.i.r.p.) is not more than that necessary for 
successful communication.

Conformément à la réglementation d’Industrie Canada, le présent 
émetteur radio peut fonctionner avec une antenne d’un type et 
d’un gain maximal (ou inférieur) approuvé pour l’émetteur par 
Industrie Canada.  Dans le but de réduire les risques de brouillage 
radioélectrique à l’intention des autres utilisateurs, il faut choisir 
le type d’antenne et son gain de sorte que la puissance isotrope 
rayonnée équivalente (p.i.r.e.) ne dépassepas l’intensité nécessaire 
à l’établissement d’une communication satisfaisante.

NOTE:  This equipment has been tested and found to comply 
with the limits for a Class B digital device, pursuant to part 
15 of the FCC Rules.  These limits are designed to provide 
reasonable protection against harmful interference in a 
residential installation.  This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference 
to radio communications.  However, there is no guarantee that 
interference will not occur in a particular installation.  If this 
equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference 
by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from 

that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician  

for help.

NOTE:  THE GRANTEE IS NOT RESPONSIBLE FOR ANY 
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED 
BY THE PARTY RESPONSIBLE FOR COMPLIANCE.  SUCH 
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO 
OPERATE THE EQUIPMENT.

©2019 QSG1

How to mount

Using one of the supplied mounts, starting from 
the front-antenna end of the detector, slide 
it into the mounting grooves on each side of 
the detector.  Position the detector so the front 
antenna looks through the windshield and the 
rear antenna has a clear view to the rear of 
your car.  Stay clear of the wipers and the black 
mask at the top of the glass.

When the detector is properly oriented, the 
driver will see this view. 

SAFETY WARNING:  Because a detector on 
a windshield mount or visor mount is not 
permanently attached to the car, it could come 
loose in a crash, possibly causing injury.  Also, 
a passenger may move forward on impact and 
contact the detector.  Keep these possibilities 
in mind when you mount your Valentine One 
Gen2.

How to connect to 12V

Plug one end of the supplied power cords into 
the detector’s RJ11 connector.  Plug the other 
end into the “MAIN” Lighter Adapter jack and 
insert the adapter into the car’s 12V socket.   
If your vehicle has only a USB socket, you’ll 
need to purchase a USB-to-12V Convertor.

   

Driver’s view

Driver’s view

A

A

A

                                

Bogey Counter

 

Blank -  Power off

 

-  Power on, All-Bogeys

®

 mode

 

- Power on, Logic

®

 mode

 

-  Power on, Advanced-Logic

®

 mode

 

-   One  bogey

 

etc. - Number of bogeys being tracked

 

- Laser warning

 

- Alert terminated; not radar

Reviews: