background image

 

 Valco Cincinnati

13-1

Section 13—Warranty

Warranty Information

Valco Cincinnati, Inc. warrants its equipment worldwide against defects in material and workmanship as outlined in
this section.

Cold-Glue Equipment and Electronic Controls

One (1) year from the date of shipment by Valco Cincinnati.

Hot-Melt Units, Hoses, Valves, and Related Equipment

All components except cast-in heating elements are warranted for a period of six (6) months from the date of
shipment by Valco Cincinnati. Cast-in heaters carry an additional, pro-rated warranty not to exceed three (3) years
from the date of shipment by Valco Cincinnati.

Liability of the company is limited to repair of the product, or replacement of any part shown to be defective, and
does not extend to defects caused by accidents, misuse, abuse, neglect, tampering or deterioration by corrosion. This
warranty does not cover those items determined by Valco Cincinnati, Inc. to be normal wear items such as seals, O-
rings, diaphragms, springs, etc.

Reconditioned equipment, unless specified otherwise at the time of purchase, will be warranted as described above
for a period of ninety (90) days from the date of shipment by Valco Cincinnati.

Components purchased by Valco Cincinnati, Inc. from others for inclusion in its products are warranted only to the
extent of the original manufacturer’s warranty. In no event shall Valco Cincinnati, Inc. be liable for indirect or
consequential damages arising out of the use of Valco Cincinnati products.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to Valco Cincinnati,
Inc. for examination and verification. If claimed defect is verified, repairs or replacements will be made F.O.B.
Cincinnati, Ohio, U.S.A. or ex-works Telford, U.K. If the inspection of the equipment does 

not

 disclose any defect

of workmanship or material, any necessary repairs will be made at a reasonable charge and return transportation will
be charged.

This is the only authorized Valco Cincinnati, Inc. warranty and is in lieu of all other expressed or implied warran-
ties, representations or any other obligations on the part of Valco Cincinnati, Inc.

Summary of Contents for VC350A








































































































































































































































































































































Reviews: