manualshive.com logo in svg

Val Controls IDC24-A, User Manual

Share
Download
Val Controls IDC24-A User Manual Download Page 37

 
 

 

DID-UM-002 

Val Controls A/S 

•

 Limfjordsvej 3 

•

 DK-6715 Esbjerg N 

•

 Tel. +45 7547 0600 

[email protected] 

•

 www.valcontrols.com 

Revision: 10 

 

 

37/74 

No. 417 

PST error: Total timeout, pressure 

Description 
 

The pressure did not reach the start pressure after the partial stroke 

Trouble shooting 
 

This error can be caused by: 

•

 

Low supply pressure 

It can be solved by: 

•

 

Increase pressure 

•

 

Resolve the mechanical problem 

•

 

Increase PST total timeout 

 

No. 418 

PST error: At 0% position 

Description 
 

The position measured to be 0% 
 

Trouble shooting 
 

This error can be caused by: 

•

 

Position sensor was disconnected 

•

 

Position sensor is operating in the illegal area 

•

 

Wrong configuration of the position switches 

•

 

The valve moved to 0% 

It can be solved by: 

•

 

Check the position sensor 

•

 

Make sure the position sensor is operating within the legal area 

•

 

Check the function of the position switches 

•

 

Decrease the PST travel 

 

 

No. 419 

PST error: Wrong Switch. SP 

Description 
 

The SP switch was activated before the 100% switch was released 

Trouble shooting 
 

This error can be caused by: 

•

 

Wrong configuration of the position switches 

 
 

 

Summary of Contents for IDC24-A











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands