manualshive.com logo in svg

Vaisala RS41, User Manual

Share
Download
Vaisala RS41 User Manual Download Page 28

User’s Guide ______________________________________________________________________

26 ___________________________________________________________________M211486EN-A

Vaisala Ozone Sounding Startup Kit

Vaisala part number 25820OS.

Vaisala Ozone Sounding Startup Kit is used when preparing a new 
ozone sounding site. The kit includes materials and equipment for the 
sounding preparations. A list of the items and their part numbers are 
provided in 

Table 5 on page 26

. More detailed information is given in 

the sections below.

Also note the following points:

-

The preparation startup kit delivered by SPC (see Operator’s 
Manual for Model 6A-ECC Ozonesonde) differs from the Vaisala 
startup kit.

-

The preparation startup kit delivered by Droplet Measurement 
Technologies (Operator Manual for Corporation Model Z 
Ozonesonde, or product brochure) differs from the Vaisala startup 
kit.

-

Triple-distilled water and some other chemicals are not delivered, 
as they are easily available on the local sites.

-

Documentation contains several manuals. Refer to section 

Related 

Manuals on page 11

 for further details.

-

Instructions for using the sounding software are needed to conduct 
a successful sounding. In addition to the instructions in this 
manual, MW41 sounding software contains an embedded on-line 
help with instructions for performing an ozone sounding.

-

The Ozonizer/Test Unit TSC-1 is traditionally used for ozone 
sensor preparation. However, these days it is possible to substitute 

Table 5

Ozone Sounding Startup Kit

Pieces Item

Vaisala Part Number

1

Ozonizer/Test Unit TSC-1

12768

1

Ozone destruction filter

13197OS

1

Pump test unit

12785OS

1

Set of laboratory ware

13198OS

1

Ozone chemicals

13199OS

1

Air flow meter

1319OS

1

Balance

12771

1

Power supply

12767

1

Ozone documentation (includes several 
manuals)

Summary of Contents for RS41





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands