manualshive.com logo in svg

Vaisala MGP260 Series, User Manual, Page: 38 / 92

Share
Download
Vaisala MGP260 Series User Manual Download Page 38

More information

‣

Installing the driver for the USB service cable (page 36)

‣

Removing probe from process (page 59)

4.2.1 Installing the driver for the USB service cable

Only Windows

â

 operating systems are supported by the driver of the USB

service cable.

1. Connect the USB service cable to a USB port on your computer. Windows

â

 detects the

new device and installs the appropriate driver.

2. Open 

Devices and Printers

 from the Windows

â

 Start menu. Use search to find it if

necessary (search for "devices").

3. Locate the cable in the list of devices: 

• If the device is listed as 

Vaisala USB Device

 with a COM port number in brackets, the

cable is ready for use. Take note of the COM port number for later use.

• If the device is listed as 

Vaisala USB Instrument Cable

 without a COM port number

listed, you must install the driver manually.

4. To install the driver manually:

a. Disconnect the USB service cable from the computer.

b. Download the Vaisala USB driver at 

www.vaisala.com/software

 (search and select the

appropriate USB Instrument Driver Setup for your cable).

c. Run the USB driver installation program 

Vaisala USB Device Driver

Setup.exe

. Accept the installation defaults.

d. Go back to 

step 1

 and verify that the driver installation works as expected.

MGP260 User Guide

M212504EN-A

36

陕西威瑞仪器仪表有限公司 生产代理销售：实验检测设备 气象科学仪器设备

Tel:029-88186182 Web:www.xavery.cn Email:[email protected]

Summary of Contents for MGP260 Series





























































































Reviews:

No comments