Vaisala IRIS User Manual Download Page 251

Page: 251 / 394

6.17.3 NDOP Output Options

NDOP

product output options are a combination of the

WIND

options and the

CAPPI

height

selection.
Because this tool works with

WIND

FCAST

NDOP

, and

CAPPI

, you may wish to leave it on

the screen.

More information

‣

NDOP : Multiple Doppler (page 167)

‣

CAPPI Height Selection Tool (page 248)

‣

WIND and FCAST Output Options (page 257)

6.17.4 VAD Output Options

During display, you can select one or all of the elevation angles in the

VAD

product.

The following figure shows an example of a single angle being displayed. This data has not
been unfolded.

Chapter 6 – Quick Look Window

RESTRICTED

249

Summary of Contents for IRIS











































































































































































































































































































































































































Search results

Summary of Contents for IRIS

Reviews:

Related manuals for IRIS

Brands by name

Popular brands

Vaisala IRIS, User Manual

Search results

Summary of Contents for IRIS

Reviews:

Related manuals for IRIS

Brands by name

Popular brands