Vaisala HMP3 User Manual Download Page 30

Page: 30 / 96

3. Locate the cable in the list of devices:

• If the device is listed as

Vaisala USB Device

with a COM port number in brackets, the

cable is ready for use.

Note the COM port number, you will need it later.

• If the device is listed as

Vaisala USB Instrument Cable

without a COM port number

listed, you must install the driver manually.

4. To install the driver manually:

a. Disconnect the USB service cable from the computer.

b. Download the Vaisala USB driver at

http://www.vaisala.com/software

(select the

appropriate USB Instrument Driver Setup for your cable).

c. Run the USB driver installation program

Vaisala USB Device Driver

Setup.exe

. Accept the installation defaults.

d. Go back to

step 1

and verify that the driver installation works as expected.

4.3 Connecting to Insight software

• Computer with Microsoft Windows

operating system and Vaisala Insight

software installed

• USB connection cable (no. 242659)

When connecting several devices at the same time, note that your

computer may not be able to supply enough power through its USB ports. Use
an externally powered USB hub that can supply >2 W for each port.

CAUTION!

HMP3, HMP4, HMP5, HMP7, HMP8, HMP9, MMP8, TMP1 User Guide

M212022EN-D

陕西威瑞仪器仪表有限公司生产代理销售：实验检测设备气象科学仪器设备

Tel:029-88186182 Web:www.xavery.cn Email:[email protected]

Summary of Contents for HMP3

































































































Search results

Summary of Contents for HMP3

Reviews:

Related manuals for HMP3

Brands by name

Popular brands

Vaisala HMP3, User Manual

Search results

Summary of Contents for HMP3

Reviews:

Related manuals for HMP3

Brands by name

Popular brands