background image

Notes on the documentation

Operating instructions ecoTEC plus  0020134822_01

3

1

Notes on the documentation

The following instructions are intended to guide you 
throughout the entire documentation. Other documents 
apply in addition to these operating instructions. 
We accept no liability for any damage caused by failure to 
observe these instructions.

Other applicable documents

When operating the ecoTEC plus, you must observe all 
operating instructions that are included with other compo-
nents of your system.
These operating instructions are included with the individ-
ual components of the system.

Further instructions for all accessories and controllers used 
also apply.
The benchmark checklist for starting up gas-fired boilers 
(contained in the installation instructions) must be com-
pleted by the Health and Safety Executive-approved heating 
specialist company and/or the competent person present 
during the commissioning and must be passed on to the 
system operator. After reading through these instructions, if 
you have any questions regarding the operation of the 
boiler, please contact your recognised Health and Safety 
Executive-approved heating specialist company or Vaillant's 
technical department.

In these instructions, the heating specialist company and 
competent person approved by the Health and Safety Exec-
utive will be abbreviated as the heating specialist company 
and competent person.

1.1 Storing 

documents

 

>

Store these operating instructions and all other applica-
ble documents in such a way that they are available 
whenever required.

1.2 

Applicability of the instructions

These operating instructions apply exclusively to boilers 
with the following article numbers:

Unit

Type designation

Article number

ecoTEC plus

VU GB 806/5-5

0010010767

ecoTEC plus

VU GB 1006/5-5

0010010780

ecoTEC plus

VU GB 1206/5-5

0010010791

1.1 Type overview

To find out the article number of your boiler, refer to the 
identification plate.

1.3  

Identification plate

The identification plate of your Vaillant ecoTEC plus boiler 
is attached at the factory to the underside of your boiler.
The seventh to sixteenth digits of the serial number on the 
identification plate represent the article number.

1.4  

CE label

The CE label shows that the units comply with 
the basic requirements of the applicable direc-
tives as stated on the identification plate.

1.5 Benchmark

i

  Vaillant Ltd. supports the Benchmark Initiative. 

A benchmark checklist for commissioning floor-
standing gas-fired boilers is attached to these 
installation instructions. It is very important that 
this document be filled out properly when 
installing, commissioning and handing-over to 
the system operator.

Summary of Contents for VU GB 806/5-5





























Reviews: