Vaillant VR 91 Operating And Installation Instructions Download Page 11

0020200905_02 Operating and installation instructions

11

You can use this function to read the
software versions of the remote control
unit.

3.10.3 Setting the address for the

remote control unit

Menu

Installer level

System config-

uration

[

System

----]

Remote control

address

You can use this function to set the ad-
dress for the remote control unit.

Every remote control unit has a unique ad-
dress, starting with Address 1. Increase
the number in the address consecutively
for each additional remote control unit
used.

3.11 Troubleshooting
3.11.1 Fault messages

If a fault occurs in the heating installation,

will appear in the display together with

a fault message.
Troubleshooting faults (

Appendix B.3)

Troubleshooting errors (

Appendix B.4)

3.12 Decommissioning
3.12.1 Decommissioning the heating

installation

Decommission all system components
of the heating installation, as described
in the installation instructions for the
individual system components.

3.12.2 Removing the product from

the wall

1.

Insert the screwdriver into the slot on
the wall base.

2.

Lever the product off the wall base.

3.

Disconnect the eBUS line from the pin
header on the product and from the
terminal block on the heat generator.

4.

Unscrew the wall-mounting base from
the wall.

3.13 Recycling and disposal
Packaging

Dispose of the packaging correctly.

This product is an electrical or electronic
unit within the context of EU Directive
2012/19/EU. The unit was developed and
manufactured using high-quality materials
and components. These can be recycled
and reused.
Find out about the regulations that apply in
your country regarding the separate collec-
tion of waste electrical or electronic equip-
ment. Correctly disposing of old units pro-
tects the environment and people against
potential negative effects.

Dispose of the packaging correctly.

Observe all relevant regulations.

Disposing of the product

If the product is labelled with this

symbol:

In this case, do not dispose of the
product with the household waste.

Instead, hand in the product to a collec-
tion centre for waste electrical or elec-
tronic equipment.

Disposing of batteries

If the product contains batteries that

are labelled with this symbol:

In this case, dispose of the batteries at
a collection point for batteries.

Prerequisite:

The batteries can be

removed from the product without
causing any destruction. Otherwise,
the batteries are disposed of to-
gether with the product.

In accordance with the legal regula-
tions, the end user is obligated to re-
turn used batteries.

Deleting personal data

Personal data may be misused by unau-
thorised third parties.

Summary of Contents for VR 91





















Reviews: