background image

- 11 -

0020140122_02 - 05/13

INSTALLATION

EN

3.3 

Type designation and serial number

Data plate location:

1

3.4 

Data plate description

The data plate certi

fi

 es the country where the product is intended 

to be installed.

The data plate contains the following data:

Abreviation/symbol

Description

Brand and Product name

Vaillant VR66

Model

Product article number

V/Hz

Voltage / Frequency

T

Temperature range

Serial-no

Product serial number

See chapter Recycling

See chapter "CE label"

VA

Power Consumption

4  Mounting and installation

i

All the dimensions shown of the illustrations are expressed in 

millimetres (mm).

4.1 

Preparing the mounting and installation

4.1.1 

Considering the product location

Before choosing a site for the appliance, carefully read the safety 

warnings and instructions in the user guide and installation 

manual.

 

Explain these requirements to the appliance user.

 

Take all necessary precautions.

Install the system:

 - in a room protected from frost, 

 - in a convenient location, accessible for wiring and servicing.

Do not install the control unit:

 - close to heat sources such as radiators, chimney walls, 

televisions, direct sunlight,

 - above a cooking device capable of generating steam and 

grease,

 - in a room with a lot of dust or with a corrosive atmosphere.

 Caution!

These pipes can become very hot which will damage 

the cables or the system.

• 

The electrical cables must not be attached to or in 

contact with the hydraulic pipes. 

1500

174

272

52

4.2 

Mounting the product

4.2.1 Opening 

the 

VR66

A

B

 

Unscrew (A) the screw securing the housing cover.

 

Pull (B) the housing cover forwards.

Summary of Contents for VR 66





















Reviews: