VAF GV900W User Manual Download Page 6

    VAF Adjustable Band Selective Repeater     

 

 

VAF Corp. 

Data Communication 

Tell:44655121 Fax: 44658496 

 

When monitoring center has not been established, technicians can 

monitor, set, modify the parameters of all the modules of repeaters and 

easily collect equipment warning information via local PC. Once the 
repeater fails, monitoring system can immediately send warning 

information to designated mobile phone or cable phones at will. 

When a monitoring center has been established, technicians can 

control repeaters by OMT software in the monitoring center or optimize 
parameters and upgrade software according to the actual situation of 

network. It will facilitate the monitoring of wireless transmission 
repeater of mobile communications. 

 

1.4

 

Technical standard 

1. GSM 05.05  “Wireless transmission and reception 

2. GSM 03.30  “Wireless network planning” 
3. GSM 11.20  “GSM base station (BBS) equipment specifications” 

4. Requirements for repeater by National Radio Administration 

Bureau 

5. YD/T952-1998  “ Technical Requirements for 900M Repeater” 
 

 
 

 
 

 
 

 
 

 

 

Summary of Contents for GV900W
























Reviews: