VADO Metiz Installation Manual Download Page 2

2

11

Please read these instructions carefully before starting installation and keep for  

future reference.
Remove all packaging and check the product for missing parts or damage before 

starting installation.
Any alterations made to this product and fittings may infringe water regulations and 

will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority 

Regulations/Byelaws and Building and Plumbing Regulations.  

To be installed in accordance with BS EN806.
We strongly recommend that you use a qualified and registered plumber.

General installation

Important - please read

Operating Specifications

Operating Pressure
Minimum operating pressure

 1 bar 

Maximum operating pressure

 5 bar

This fitting is a mixing device and therefore water supplies should be reasonably 

balanced.
When installed, the fitting must comply with the requirements of the Water Supply 

(Water Fittings) Regulations 1999 and Scottish Byelaws 2004. 

For further information, contact the Water Regulations department of your local water 

supplier (see the WRAS website www.wras.co.uk for details) or the Water Regulations 
Advisory Scheme by email (info

@

wras.co.uk) or telephone: 01495848454.

Before making any inlet pipe connections, all supply pipes MUST be thoroughly flushed 

to remove debris. Failure to do so could result in damage or low flow from the mixer 

unit. Water Supply (Water Fittings) Regulations 1999 Schedule 2 Section 13.
The fitting of isolating valves to the inlet feeds is advised for ease of maintenance.
Please take great care when installing this mixer not to damage its surface.
Please note if installing in an enclosed environment, access should be left for servicing 

and maintenance. No costs relating to inadequate access can be accepted.

Guarantee

All VADO V products come with a 2 year guarantee as standard.  Within this guarantee 

period VADO will provide replacement parts needed to complete the product repair. 
This standard guarantee may be extended by registering your product to give up to a 12 

year guarantee period. Once registered:

Guarantee conditions

Our products are guaranteed against manufacturing defects from the date of purchase 

until the expiry of the relevant guarantee period shown above.
The guarantee is only valid if: 
•The product has been installed, used and maintained in accordance with VADO's            

  instructions and subjected to normal use only.
•The defect is not due to use of an unsuitable or inadequate water or power supply.
•The defect is not due to accident, misuse, neglect or incorrect/inappropriate repair        

  (other than by VADO or VADO authorised agents) or damage caused by foreign objects   

  or substances.
•The extended guarantee is only available if you have completed the Guarantee 

  Registration Process. This can be done via the VADO website or via phone to our  

  aftersales team. Registration must be completed within 6 months from date  

  of purchase. 
Under the extended guarantee period VADO will, at its option, offer to supply any 

replacement product (or component part) assessed to be defective 

[SEE NOTE  1]

The guarantee (whether standard or extended) is non-transferable to any subsequent 

owner.
All claims under the guarantee should be notified in the first instance to our Aftersales 

department, contact details below, this must be done no later than the last day of the 

relevant guarantee period. All claims must be accompanied by proof of purchase (sales 

receipt or delivery note) from an official VADO dealer.
The guarantee does not extend to any consequential loss or damage. 
After repair or replacement, the relevant guarantee period will be calculated from the 

original date of purchase. 
VADO operates a policy of continuous product development and therefore reserves 

the right to change the product, packaging and documentation specifications without 

notice.

NOTES:
[1] VADO reserves the right to charge in advance for a product (or replacement part) 

pending collection and investigation (at VADO expense) to confirm a defect is due to a 

manufacturing issue.  If a defect is found the charge will be refunded or cancelled.

This guarantee is in addition to and does not affect your statutory rights as a consumer. 
Tel: 01934 745163
Email: [email protected]

Summary of Contents for Metiz







Reviews: