Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 103 | Manualshive

Page: 103 / 138

background image

RDA 400S

27.06.2011
ver.2

103

5.14 Changing the valve seals on the lifting ram

Figure 5.25

NOTE!

When servicing the hydraulic system, the side sections and the seed drill should be low-

ered, with zero pressure in the respective hydraulic circuit

A

Remove hose (F), with care if there is any pressure left in the system.

B

Remove the seat (E), the guide (C) and the piston (A).

C

If leaking externally, change the O-ring (B) part no. 407021. If leaking internally change the
seal in the seat (E): First put the O-ring in place in the groove. Put the seal in hot water first,
and press it into a kidney shape to fit it.

NOTE!

The edge side of the seal should be turned to-

wards the piston. Use a blunt object to move the seal into place. Carefully insert the piston to
help restore the seal to its round shape.

D

Reassemble the valve. Do not forget the two rubber/steel washers.

The valve on the bottom of the lifting ram shuts off the oil flow from the ram after lowering to the
preset working depth.

Working depth is set with the depth stop (A), which actuates the valve via valve rod (D). If the
stop moves along the piston rod so that the working depth gradually increases, the valve is prob-
ably leaky.

«
...
101
102
103
104
105
...
»

Summary of Contents for Rapid RDA 400S











































































































































Reviews:

No comments

Related manuals for Rapid RDA 400S

Relion 670 series

Brand: ABB Pages: 66

Brand: GE Pages: 138

Brand: GE Pages: 24

Brand: C.M.O Pages: 10

Brand: Bartscher Pages: 28

Brand: Bartscher Pages: 13

Brand: IBEX Pages: 10

Brand: M-system Pages: 12

Brand: Tabi Pages: 8

Brand: Dabi Atlante Pages: 102

Brand: XanLite Pages: 4

Brand: Rapala Pages: 14

Brand: S.R.Smith Pages: 43

Brand: Waters Pages: 250

Brand: Waters Pages: 141

Brand: Olympus Pages: 130

UG 2200 Special

Brand: Amazone Pages: 252

Brand: HOFFEN Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands