VADDIO RoboTRAK Integrator'S Complete Manual Download

Page: 57 / 74

camera master tracking

Stop or start tracking mode. Tracking mode should be off (stopped) for direct operation of the video camera.

Synopsis

camera master tracking [ stop | resume ]

Parameters and
Values

stop

halts tracking and park cameras at the home
position

resume

starts tracking

Example

camera master tracking stop

Takes the system out of tracking mode.

camera master recalibrate

Executes a pan-tilt reset. This takes a few seconds.

This command is for the RoboTRAK IR camera only. It is not used for video cameras.

Synopsis

camera master recalibrate

Example

camera master recalibrate

camera master standby

Gets or sets the IR camera's standby state.

To control whether the video camera goes to standby mode when the IR camera does, use the command

camera master standby config peripheral

Synopsis

camera master standby [ get | on | off | toggle ]

Parameters and
Values

get

Returns the current standby status for the IR
camera.

Places the IR camera in standby mode.

off

Brings the IR camera out of standby, placing it
in full-power mode.

toggle

Changes the IR camera's standby state - if it
was in standby mode,

toggle

brings it to full-

power mode, and vice-versa.

Examples

camera master standby on

Places the IR camera in standby mode.

camera master standby get

standby:

off

Returns the IR camera's current standby state – standby is off, meaning
the camera is in full-power mode.

Integrator's Complete Guide to the RoboTRAK Presenter Tracking System

Summary of Contents for RoboTRAK











































































Search results

Summary of Contents for RoboTRAK

Reviews:

Related manuals for RoboTRAK

Brands by name

Popular brands

VADDIO RoboTRAK, Integrator'S Complete Manual

Search results

Summary of Contents for RoboTRAK

Reviews:

Related manuals for RoboTRAK

Brands by name

Popular brands