background image

3

Parts

1.

 Hose   

2.

 Hose Hanger   

3.

 Dusting Brush 

4.

 Upholstery Tool   

5.

 Crevice Tool   

6.

  Telescopic  Wand   

7.

 Floor Brush   

8.

 Tool Storage Bag

1

2

3

4

5

6

7

8

 Cuff 

For use when using the Blowing Feature.
See Pg. 7 for details.

HEPA Bag (

HPB2H)

Must be installed onto the bag stem 

before use.

See Pg. 8 for details.

Replacements sold in 3 pack

Part #: HPB2HPK

Protector Plate (PP101) 

This plate should already be installed 

in your unit when you receive it, just 

below the HEPA bag.  
Be sure it is face up. (Pg. 5 for details.)

Cannot be plumbed for use as a central vac.

DO NOT USE AS A WET VAC

Utility Valve

Use for “Vacuuming”

(Must be held open with 

additional cuff, when 

wanting to use the Blow 

feature)

Exhaust

Use for “Blowing”

Lid

HEPA Bag is located inside the 

unit, below the lid.

On/Off switch

Additional tools needed for installation:

•  Level

•  Rubber Mallet

•  Electric Drill

•  1/8” drill bit

(If mounting on block or concrete wall, 

you will need masonry bit & plastic or 

lead anchors - not provided)

1

2

3

4

5

6

7

8

Tool kit for standard Garage Vac

Tool kit for Garage Vac PRO

Other items included with this system...

Latches

Summary of Contents for GARAGE VAC













Reviews: