Vacon 100 HVAC Applications Manual Download

Page: 96 / 201

7.3

REAL TIME CLOCK

Table 51: The real time clock parameters in the I/O and Hardware menu

Index

Parameter

Min

Max

Unit

Default

Description

V5.5.1

Battery State

2205

Status of the battery.

1 = Not installed

2 = Installed

3 = Replace the battery

P5.5.2

Time

hh:mm:

2201

The current time of the

day

P5.5.3

Date

dd.mm.

2202

The current date

P5.5.4

Year

yyyy

2203

The current year

P5.5.5

Daylight Saving

2204

The daylight saving

rule

1 = Off

2 = EU: starts on the

last Sunday in March,

ends on the last Sun-

day in October

3 = US: starts on the

2nd Sunday in March,

ends on the 1st Sunday

in November

4 = Russia (permanent)

7.4

POWER UNIT SETTINGS

In this menu, you can change the settings of the fan and the sine filter.

The fan operates in the optimised or the always on mode. In the optimised mode, the internal

logic of the drive receives data about the temperature and controls the fan speed. After the

drive goes in the Ready state, the fan stops in 5 minutes. In the always on mode, the fan

operates in full speed, and does not stop.

The Sine filter keeps the overmodulation depth in limits and does not let the thermal

management functions decrease the switching frequency.

VACON · 96

I/O AND HARDWARE MENU

TEL. +358 (0)201 2121 · FAX +358 (0)201 212 205

Summary of Contents for 100 HVAC










































































































































































































Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands

Vacon 100 HVAC, Applications Manual

Search results

Summary of Contents for 100 HVAC

Reviews:

Related manuals for 100 HVAC

Brands by name

Popular brands