V7 CHGCT30i Manual Download Page 3

SAFETY AND WARNINGS

CAUTION

!

This symbol on the product indicates important 

literature concerning operation and maintenance. 

Do not remove or alter labels.

Check

 www.v7world.com

 

for additional support and

installation information.

2

This product uses UV-C light. Warning: eye and skin damage may result from direct exposure
to the light produced by these lamps. 

Do not activate LEDs with doors open. To safely use the 

UV-C LEDs kit, the system  requires to always close both doors completely: left door first and 

then right door, closing the handle. 

By following this instructions, the product prevents 

automatically any accidental exposure.

Never look at lamps while they are on, lit or illuminated.

Disconnect power to all UV-C devices before any maintenance operation

This product has a security system to automatically prevent accidental exposure. Do not alter 
this system. Do not try by any means to fake doors' closing

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation.”

Caution: no changes or modifications allowed on the equipment not expressly approved by the 
party responsible for compliance. It could void the user's authority to operate the equipment. 

Please refer to Charge Cart’s user manual for warnings regarding the Charge Cart itself.

This product has been designed to work with cart’s doors closed. Follow installation instructions: 

do not change any steps of the installation or product.

WARNING: UV emitted from this product. Avoid eyes and skin exposure to unshielded product.

Summary of Contents for CHGCT30i





















Reviews: