E
N
G
L
IS
H
ANEMOMETER WITH SUN AND
TEMPERATURE SENSOR – REMOTE CONTROL
The HURRICANE-RS sensor detects the sun, wind, and
temperature parameters and transmits them by radio to the
remote controller.
If the SUN threshold is exceeded, an OPEN command is sent to
the sunshade, whereas if the WIND threshold is exceeded, a
CLOSE command is sent.
Using 2 buttons and 8 LEDs, the thresholds for the sensors can
be set and the device can be memorized on the controlled
remote controller.
To install HURRICANE-RS, carefully read these instructions.
CAUTION: If the system is left unattended for long periods,
we recommended that the sunshade be closed and that
the sun sensor's automatic function be deactivated.
TECHNICAL DATA
1. DEVICE MEMORIZATION ON REMOTE
CONTROLLERS
1.
Move to a position close to the remote controller that will be
controlled
2.
Power the device with a temporary cable
3.
If the sunshade is controlled with transmitters in the
DUO
series, use a remote control that is already memorized in the
controller and proceed as follows:
a.
Press SELC on the transmitter a few times, until the LEDs
display the channel memorized (only DUO6 and DUO4)
b.
Return the awning to its mid-height
c.
Move Switch 1 on the transmitter to the ON position
d.
Press and hold down PROG on the transmitter for about 5
seconds, until the motor starts to move
e.
Release PROG and the motor will stop
f.
Press
P1
on HURRICANE-RS for at least 2 seconds (Fig.2)
g.
To check that it has been memorized correctly, press
P1
:
the sunshade should CLOSE. If not, repeat the procedure
4.
If the sunshade is controlled with transmitters in the
ADLER
series, use a remote control that is already memorized in the
controller and proceed as follows:
CAUTION:
If the remote control used has multiple channels,
first select the channel memorized in the controller using C.
a.
Press and hold down the UP and DOWN buttons on the
remote control until the motor starts to move in one
direction.
b.
Release the buttons and the motor will stop.
c.
Within 8 seconds, press
P1
on HURRICANE-RS for at least
2 seconds
d.
To check that it has been memorized correctly, press
P1
:
the sunshade should CLOSE. If not, repeat the procedure.
2. INSTALLATION
CAUTION:
For correct operation, please remember that the
sensor must be positioned near the sunshade it protects and in
an area exposed to sun and wind.
The articulated arm should be parallel to the ground and
the blades should be turned downwards (Fig. 3).
Before attaching the device, make sure the radio coverage is
sufficient: put HURRICANE-RS in the position for installation and
press
P1
. Check that the sunshade closes.
CAUTION:
Check that there are no other devices operating on
the same frequency (434.15 MHz) and with continuous
transmission, such as alarms, radio headphones, etc., which may
interfere with the communication between the sensor and the
command controller. Installing more HURRICANE-RS sensors in
the same area could give rise to the same problem.
If the radio channel is not accessible for more than 15 minutes,
for safety reasons the controller closes the sunshade and blocks.
The system will return to normal operation once the controller
again receives the radio signal from the sensor.
To force exit from the BLOCK state, power must be disconnected
from the command controller for a few seconds.
1.
Remove the cover (Fig. 1)
2.
Attach the device to the wall using the provided wall plugs
(Fig. 1)
3.
Position the articulated arm horizontally with the blades
turned downwards (Fig. 3)
CAUTION:
If the articulated arm is not perfectly horizontal there
may be problems detecting the wind speed.
4.
Tighten the screw,
V1
(Fig. 3), to lock the movement of the
arm
3. ELECTRICAL WIRING
1.
Connect a power grid cable (2 x 1.5 sq. mm section) on the
L
and
N
terminals
2.
Block the cable using the provided cable gland
3.
Close the cover
Maximum applicable voltage
230 V ~ 50Hz
Absorbed power
3,5 W
Transmission frequency
434,15 MHz
Protection
IP44
Temperature for use
-20 ÷ +60 °C
