background image

 

Version 26.04.2021 

        HW: 16(V65) 

     VL2-RTI11-5 

P

a

g

e

3

 

 

Legal Information 

 

By law, watching moving pictures while driving is prohibited, the driver must not be 
distracted. We do not accept any liability for material damage or personal injury resulting, 
directly or indirectly, from installation or operation of this product. Apart from using this 
product in an unmoved vehicle, it should only be used to display fixed menus or rear-view-
camera video when the vehicle is moving (for example the MP3 menu for DVD upgrades). 

 

Changes/updates of the vehicle’s software can cause malfunctions of the interface. Up to 
one year after purchase we offer free software-updates for our interfaces. To receive a free 
update, the interface has to be sent in at own cost. Wages for de-and reinstallation and 
other expenditures involved with the software-updates will not be refunded.  
 
No liability for vehicle wire colours and pin definition! 
Changes by the vehicle manufacturer are possible. The given information has to be verified 
by the installer. 
 

 

1.

 

Prior to installation 

 

Read the manual prior to installation. Technical knowledge is necessary for installation. The 
place of installation must be free of moisture and away from heat sources. 
 
1.1.

 

Delivery contents 

 

 
 
 
 
 

 

 
 
 
 
 
 
 

 

 

 
 
 
 
 

 

Take down the serial number of the interface and store this manual for support 
purposes:  ____________________

 

Summary of Contents for VL2-RTI11-5





















Reviews: