V-Gear LanDisk Advance User Manual Download Page 13

Page: 13 / 13

Please do not close the window or turn the power off, until the success message dialog has been shown as below:

3.Press “Restart” and wait about 30 seconds then refresh this page by pressing “Refresh button” on IE browser, or reboot the

LANDISK.

4-2 Factory Defaults

You can Press “Reset” here then refresh this page by pressing “Refresh button” on IE browser, or reboot the

LANDISK to recall all settings back to factory default status.

5.FAQ

Does LANDISK have any Power saving function?

Yes, if there is no R/W in 15 minutes, LANDISK will spin down the HDD to protect and save power.

How does the DHCP service of LANDISK work?

If LANDISK has been located in the network environment, which has no DHCP server, LANDISK will turn it self

into a DHCP server, the LANDISK will detect if there has any DHCP server existing, if yes, the LANDISK will

prevent the DHCP service, and becomes a DHCP client.

What is the protocol that LANDISK follows to achieve the data sharing functions?

LANDISK is a device that based on Samba Server to achieve its data sharing function, its SMB protocol (Server

Message Block) crosses TCP/IP, NETBUEI and IPX/SPX, in short, as long as the client has supported either

TCP/IP, NETBUEI or IPX/SPX, it can use LANDISK as a FTP server.

Visit http://vgear.com for more FAQ or firmware updates.

Summary of Contents for LanDisk













