background image

1.4 Power on the scale 

a. Before plugging the power adaptor into 

electricity outlet, check and make sure 

that the input voltage of power adaptor 

matches with the output voltage of the 

outlet. If not, do not plug in and contact 

your dealer immediately. 

b. Before first time use, plug the adaptor 

into the wall outlet and charge the scale 

for at least 8 hours. 

c. After battery is fully recharged, remove 

adaptor from scale. Apply the rubber cap 

(

FIG 2 E

) to seal the DC input jack of 

scale.  

 

2. SPECIFICATIONS 

 

Model No. 

Capacity  Division  Accuracy  Min.Load 

DM-3000 

3000g 

1g 

1/3000 

20g 

DM-6000 

6000g 

2g 

1/3000 

40g 

DM-15K 

15kg 

0.005kg 

1/3000 

0.1g 

DM-30K 

30kg 

0.01kg 

1/3000 

0.2g 

DM-1100 

1100g 

0.1g 

1/11000 

2g 

DM-11K 

11kg 

1g 

1/11000 

20g 

Tare Range  Full tare range (Subtractive) 

Display 

5 x 24mm LCD display 

Operation 
Environment 

0

o

~40

o

C (32

o

~104

o

F),  

Non-condensed. R.H.

¡

Ø

85% 

Power source By Built-in rechargeable battery or power 

adaptor 

Specifications subject to change without notice 

 

NOTE  

To comply with the law of certain countries 

and certain approval requirements, the 

imperial weight units may be disabled. Contact 

your dealer for more information. 

Summary of Contents for DM-1100













Reviews: