manualshive.com logo in svg

UTICA BOILERS UH15B-060K, Installation, Operation & Maintenance Manual

Share
Download
UTICA BOILERS UH15B-060K Installation, Operation & Maintenance Manual Download Page 2

KEEP THIS MANUAL NEAR BOILER 

RETAIN FOR FUTURE REFERENCE

2

VERIFY CONTENTS RECEIVED

Fully Assembled Boiler

Vent Damper         

Draft Hood

        

Pump (Optional)

*Drain Valve

*ASME Safety Relief Valve

*Tridicator

*Black  Iron  Fittings                 

(see parts list for sizes 

and use)

Includes Essential           

Documents and Warranty

11x17 Wire Diagrams

Document Package

*Junction Box

*Circulator Harness

  

* Items found in parts box included with your boiler.

Information and specifications outlined in this manual in effect at the

time of printing of this manual.  

Manufacturer

 reserves the right to

discontinue, change specifications or system design at any time without 

notice and without incurring any obligation, whatsoever.

For Parts lists see manual  included with your boiler literature package.

 PN 240012809, Rev. D [08/15/2021]

VERIFY CONTENTS RECEIVED

Summary of Contents for UH15B-060K

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands