background image

20

CHECKING AND ADJUSTING

Adjust Pilot Burner

Pilot 

fl

 ame should surround 3/8” to 1/2” of pilot sensor. See 

Figure 15.
To adjust Flame.

1. 

Remove screw cover over pilot adjusting screw. See 

Figure 14.

2. 

Insert small screwdriver and adjust 

fl

 ame as needed. 

Turn screw counterclockwise to increase 

fl

 ame, clock-

wise to decrease.

3. 

Replace screw cover over pilot adjusting screw. 

Main Burners

•  Main burners do not require primary air adjustment and 

are not equipped with primary air shutters. 

• Main burner 

fl

 ames form sharp blue inner cones in 

softer blue outer mantel, with no yellow. Remain still 

when observing main burner 

fl

 ames.

•  Check main burner ori

fi

 ces, burner throat and 

fl

 ame 

ports for dust and lint obstruction if 

fl

 ame appearance 

is not correct. 

•  Remove rollout shield if necessary to observe main 

burner 

fl

 ames. See Figure 16.

•  Replace rollout shield after observation. 

Gas Valve Safety Shutdown Test

1. 

Test ignition system safety shutoff device after placing 

boiler in operation. 

2. 

Boilers equipped with intermittent ignition, with 

main burners 

fi

 ring, disconnect ignition cable from 

intermittent pilot control box. Gas valve will shut off 

main burners. 

3. 

TURN OFF ELECTRIC POWER to boiler before 

reconnecting ignition cable, to prevent electric shock.

 Figure 15 - Pilot Burner

 Figure 16 - Main Burner

Summary of Contents for PEG075EID

































Reviews: