连接接口
Specification
连接接口
8
Port Ethernet Switch
3
4
8
Port Ethernet Switch
Item
8 ports Ethernet Switch
Power
Power Supply
Power
adapter
Voltage
range
DC12V~24V
Consumption
＜
5W
Ethernet
Port
Parameter
Ethernet Port
1
～
8
ports: default mode: 10
/
100BASE-TX;CCTV
mode:10BASE-T;
UPLINK
Ethernet port:10
/
100
/
1000BASE-T;
SFP:1000BASE-X
Transmission Distance
Downlink port: default
mode: 0
～
150m; CCTV
mode: 0
~
250m
Uplink
port: 0
～
150m
SFP: depends on SFP module performance
Transmission
Medium
Cat5e/6 network cable
Ethernet
Exchange
Specification
Ethernet Standard
IEEE802
.
3
10BASE
-
T; IEEE802
.
3u
100BASE
-
TX;
IEEE802
.
3ab 1000BASE
-
TX;
IEEE802
.
3z
1000
-
SX
/
LX; IEEE802
.
3
X
Switch Capacity
5.6Gbps
Packet Forwarding Rate
4.17Mpps
Packet
Buffer
1M
MAC
Address
8K
Indicator
Status
Power Indicator Light
1 pc red Light
CCTV
Indicator Light
1
pc
(
green
),
the
green
light on Indicates
CCTV
Mode
start
Optical Port LED indicator
1pc SFP port working indicator light: green
Uplink
Ethernet
Port
Indicator
1
pc network working status: green light on RJ 45 port
Downlink Ethernet Port Indicator
1~8
ports: green light indicates network status, yellow light off
Protection
Port
Lighting Protection
6KV , Per: IEC61000
-
4
-
5
ESD
, Per: IEC61000
-
4
-
2
6KV/ 8KV
Operation
Environment
Working
T
emperature
-40
~
75
℃
℃
Storage
Temperature
-
40
~
85
℃
℃
Humidity
（
Non
-
condensing)
0
~
95
%
Mechanical
Dimension
（
L
×
W
×
H
）
159mm×110mm×46.5mm
Material
Aluminum
Color
Black
Weight
545g
Products are subject to change without prior notice
Please
follow
the
following
installation
steps
1
)
Please
turn
off
the
signal
source
and
the
device
'
s
power, installation
with
power
on
may
damage
the
device
;
2
)
Use
8pcs
network
cables
to
connect
8pcs
IP
cameras
with the product
'
s1
~
8 RJ45 Ethernet
ports
;
3
)
Use
another
network
cable
or
(
optical
fiber
)
to connect switch’s UPLINK
port with NVR
or
computer
;
4
)
Connect switch
with
power
adapter
;
5
)
Check
if
the
installation
is
correct
and
device
is
good
,
make
sure
all
the
connection
is
reliable
and
power
on
the
system;
6
)
Make
sure
every
network
device
has
power
supply
and
work
normally
.
连接接口
Trouble
Shooting
Please find the following solution when the device doesn't work
Please confirm if the installation is correct;
Please confirm if the RJ45 cable order is in accordance with the EIA/TIA568A or 568B industry
standards;
Please replace a
device with a properly functioning one to check if the device is broken;
If the problem still exists, please contact the factory.
failure
RJ
45
Making
Method
Tools to make RJ45: wire
crimper, network tester.
Wire sequence
of
RJ45
plug should conform with EIA/TIA568A or EIA/TIA568B standard.
1) Strip off the 2cm insulating layer to expose the 4 pairs UTP cable;
2) Seperate the 4 pairs of UTP cable and straighten them;
3) Line up the 8 separated pieces of cables per EIA/TIA 568A or 568B;
4) Cut the cables to leave 1.5cm bare wire and make sure 8 thread ends are flat and neat ;
5) Insert 8 cables into RJ45 plugs, make sure each cable is inserted in each pin;
6)Then use wire crimper to crimp the RJ45;
7) Do the above 5 steps again to make the another end of the twisted pair and make sure consistent
cable order between two ends ;
8) Using network tester to test the cable.
P
in
color
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
1
2
3
4
5
6
7
8
Pin
color
1
2
3
4
5
6
7
8
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
EIA/TIA 568A
EIA/TIA 568B
Notice
Make sure both ends use EIA/TIA568A connection method when using RJ45 port.
Make sure both ends use EIA/TIA568B connection method when using RJ45 port.
