is within detection range of the detector. If the LED does
not stay on for 4 seconds, move the detector and retest.
LED indications
The red LED located on the front of the detector indicates the
status of the detector as shown in Table 2 below.
Table 2: LED indications
Status LED
indication
Power on
Flashes once when power is applied.
Clap test/alarm
memory
In response to the clap test: Flashes twice to
indicate the detector has power and is functioning
properly; or On for 4 seconds to indicate the
detector has alarmed.
Alarm
On for 4 seconds with relay when breaking glass is
detected.
Test mode
On for 4 seconds with relay, then flashes for 60
seconds. Each test trigger resets the test mode
clock and the LED starts over flashing for 60
seconds.
4
ShatterPro 3 Glassbreak Detector Installation Instructions
Hand-clap test and alarm memory
To check alarm memory and detector operation with the hand-
clap test, do the following:
1. Standing under the detector, clap your hands together.
2. Observe the LED on the detector.
If the detector has power and is functioning properly, the LED
quickly flashes twice.
If the detector has alarmed, the LED will light for 4 seconds.
Cycle power to clear the alarm memory.
Caution:
The hand-clap test is intended as a functional test
and is not an accurate indication of detector range.
Maintenance
When installed and used properly, the detector provides years
of service with minimal maintenance. You should test the
detector annually to ensure proper operation.
Clean the cover with a damp (water) cloth as needed to keep it
free of dust and dirt. Always test the detector after cleaning it.
Specifications
Input voltage
9.5 to 16 VDC
Current
Typical
Maximum
15 mA
25 mA
Electrical configuration Form A, Form C
Relay rating
16 V, 50 mA max.
Tamper switch rating
12 V, 50 mA max.
Detection range
3 to 25 ft. (0.9 to 7.6 m) x 360°
Alarm response
4 seconds
Minimum glass size
12 x 24 in. (30.5 x 61 cm)
Recommended glass
thickness
Plate
Tempered
Wired
Laminated
3/32 to 1/4 in. (2.4 to 6.4 mm)
1/8 to 1/4 in. (3.2 to 6.4 mm)
1/4 in. (6.4 mm)
1/4 in. (6.4 mm)
Operating temperature
32 to 122°F (0 to 50°C)
Relative humidity
10 to 90% noncondensing
Dimensions
Rectangle housing
(DxWxH)
Round housing
0.81 x 2.75 x 4.52 in. (2.1 x 2.75 x 4.52 cm)
0.81 (2.1 cm) depth, 4.0 in. (10.2 cm)
diameter
Color white
Field wiring size
18 to 24 AWG
Regulatory information
UL listings
CUL, ULC-S306, UL 639
FCC compliance
This device complies with part 15 of the FCC
rules. Operation is subject to the following
conditions:
This device may not cause harmful interference.
This device must accept any interference
received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved
by the party responsible for compliance could
void the user’s authority to operate the
equipment.
Certification
Product ordering
Product
Description
5812NT
ShatterPro 3, rectangular housing, Form A
R5812NT ShatterPro 3, round housing, Form A
5815NT
ShatterPro 3, rectangular housing, Form C, tamper switch
R5815NT ShatterPro 3, round housing, Form C, tamper switch
Accessories
5709C
Glassbreak hand-held tester
Contact information
For customer support:
www.interlogix.com/customer-support
Copyright © 2011 UTC Fire & Security. All rights reserved.
