background image

5

 

IMPORTANT:  Read this entire manual before installing 

and  operating  this  product.    Failure  to  do  so  may 

result in property damage, bodily injury, or even death.  

Proper installation of this stove is crucial for safe and 

efficient operation.

 

Install  vent  at  clearances  specified  by  the  vent 

manufacturer. 

 

Do not connect the pellet vent to a vent serving any 

other appliance or stove.

 

Do  not  install  a  flue  damper  in  the  exhaust  venting 

system of this unit.

 

Use of outside air is not required for this unit.   

 

Contact  your  local  building  officials  to  obtain  a 

permit and information on any additional installation 

restrictions or inspection requirements in your area.

 

Do  not  throw  this  manual  away.   This  manual  has 

important  operating  and  maintenance  instructions 

that you will need at a later time.  Always follow the 

instructions in this manual.

 

This appliance is designed for the use of pelletized fuel 

that meet or exceed the standard set by the Pellet Fuel 

Institute(PFI), The use of other fuels will void warranty.

 

Never  use  gasoline,  gasoline-type  lantern  fuel, 

kerosene,  charcoal  lighter  fluid,  or  similar  liquids  to 

start or ’freshen up’ a fire in this stove.  Keep all such 

liquids well away from the stove while it is in use.

 

A working smoke detector must be installed in the same 

room as this product.

 

Do not unplug the stove if you suspect a malfunction.  

Turn the ON/OFF SWITCH to ”OFF’ and contact your 

dealer.

 

Your stove requires periodic maintenance and cleaning 

(see ”MAINTENANCE ”). Failure to maintain your stove 

may lead to improper and/or unsafe operation.

 

Disconnect  the  power  cord  before  performing  any 

maintenance!  NOTE: Turning the ON/OFF Switch to 

”OFF” does not disconnect all power to the electrical 

components of the stove.

 

Never try to repair or replace any part of the stove un-

less instructions for doing so are given in this manual.  

All other work should be done by a trained technician.

 

Do  not  operate  your  stove  with  the  viewing  door 

open.   The  auger  will  not  feed  pellets  under  these 

circumstances and a safety concern may arise from 

sparks or fumes entering the room.

 

Allow  the  stove  to  cool  before  performing  any 

maintenance or cleaning.  Ashes must be disposed 

in a metal container with a tight fitting lid.  The closed 

container  of  ashes  should  be  placed  on  a  non-

combustible surface or on the ground, well away from 

all combustible materials, pending final disposal.

 

The exhaust system should be checked monthly during 

the burning season for any build-up of soot or creosote. 

 

Do not touch the hot surfaces of the stove.  Educate all 

children on the dangers of a high-temperature stove. 

Young children should be supervised when they are 

in the same room as the stove.

 

The hopper and stove top will be hot during operation; 

therefore, you should always use some type of hand 

protection when refueling your stove.  

 

A power surge protector is required.  This unit must 

be  plugged  into  a  110  -  120V,  60  Hz  grounded 

electrical outlet. Do not use an adapter plug or sever 

the grounding plug. Do not route the electrical cord 

underneath, in front of, or over the heater.  Do not route 

the cord in foot traffic areas or pinch the cord under 

furniture.

 

The heater will not operate during a power outage. If a 

power outage does occur, check the heater for smoke 

spillage and open a window if any smoke spills into the 

room.

 

The  feed  door  must  be  closed  and  sealed  during 

operation.

 

Never block free airflow through the open vents of the 

unit.

 

Keep foreign objects out of the hopper.

 

The moving parts of this stove are propelled by high 

torque electric motors.  Keep all body parts away from 

the auger while the stove is plugged into an electrical 

outlet.  These moving parts may begin to move at any 

time while the stove is plugged in.

 

Do not place clothing or other flammable items on or 

near this stove. 

 

When  installed  in  a  mobile  home,  the  stove  must 

be grounded directly to the steel chassis and bolted 

to  the  floor.    WARNING—THIS  UNIT  MUST  NOT 

BE  INSTALLED  IN  THE  BEDROOM  (per  HUD 

requirements).    CAUTION—THE  STRUCTURAL 

INTEGRITY OF THE MOBILE HOME FLOOR, WALL, 

AND CEILING/ROOF MUST BE MAINTAINED.  

  

This appliance is not intended for commercial use.

* This appliance is a freestanding heater.  It is not intended to be attached to any type of ducting.  It is not a furnace.

Safety Precautions

Summary of Contents for 5520





























Reviews: