CAUTION (AS REQUIRED BY THE CALIFORNIA STATE FIRE MARSHAL)
"Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms
and areas of the household as follows. A smoke alarm installed in each separate sleeping area (in the
vicinity of, but outside of the bedrooms), and heat or smoke detectors in the living rooms, dining rooms,
bedrooms, kitchens, hallways, attics, furnace rooms, closets, utility and storage rooms, basements and
attached garages."
Page 9
THIS PRODUCT IS LISTED TO UL STANDARD FOR SAFETY,
UL217 BY UNDERWRITERS LABORATORIES, INC.
Blinks On once
approx every
40-45 seconds
Stays On
Condition:
AC Power is present. DC Power is present.
Recommendation:
None, alarm is operating properly.
Blinks On once
approx every
40-45 seconds
Off
Condition:
AC Power is not present and alarm is receiving DC Power.
Recommendation:
Check the breaker or fuse box for power. If
the breaker or fuse box looks normal, call a licensed electrician
for assistance.
OPERATIONAL SUMMARY
Silent
Silent
Blinks On
approx every
2 seconds
Stays On
Condition:
Nuisance Alarm.
Recommendation:
If there is no hazard present, verify the alarm is
mounted in the correct location (see User's Manual, "AVOID THESE
LOCATIONS" section). Reset alarm as instructed below.
Horn does not
sound when other
alarms are active
or horn does not
sound when
interconnected
alarms' test button
is pressed
Blinks On once
approx every
40-45 seconds
Stays On
or Off
Condition:
One or more alarms not responding to interconnected alarm.
Recommendation:
Press and hold the smoke alarm Test/
Silence button for at least 5 seconds. If still no alarm, turn off
AC Power at the circuit breaker or fuse box and disconnect the
alarm from the mounting bracket and make sure the connector
plug is securely attached on units that did not alarm. If still no
alarm, have a licensed electrician check to see if the yellow
wire is connected to the neutral wire.
3 Beeps,
2 second pause,
Repeat
Blinks On
approx every
2 seconds
Stays On
Condition:
Originating Smoke Alarm.
Recommendation:
If hazard is identified, please take all precautions
if an alarm sounds by calling an Emergency Service and getting out
of the home.
3 Beeps,
2 second pause,
Repeat
Off
Stays On
C o n d i t i o n :
N o n - o r i g i n a t i n g S m o k e A l a r m . A n o t h e r
interconnected smoke alarm has sensed smoke, causing all
interconnected units to alarm.
Recommendation:
If hazard is identified, please take all precautions
if an alarm sounds by calling an Emergency Service and getting out
of the home.
Blinks On once
approx every
40-45 seconds
(normal operation
mode) or Blinks on
once approx every
10 seconds
(silence mode)
Stays On
Condition:
One alarm has sensed smoke.
Recommendation:
QUICK FIND
®
Alarm Origination - In an
interconnected system, it is difficult to determine which alarm initiated
the alarms to sound. The QUICK FIND
®
feature will allow you to
immediately locate the originating alarm (once the alarms have
stopped sounding). To initiate QUICK FIND
®
, press the Test/Silence
button on any alarm. After releasing the button, the originating alarm
will continue to sound for approx 60 seconds. In a non-interconnected
installation, it is necessary to test each alarm to determine the
originating alarm.
Blinks On once
approx every
40-45 seconds
Stays On
Condition:
Alarm needs to be reset due to varying conditions/
previous alarms.
Recommendation:
To Reset the Alarm, hold the Test/Silence button
for approx 10 seconds. This will clear alarm origination. Reset after
each smoke alarm event.
Silent
1 Chirp
approx every
40 seconds
Stays On
Condition:
Low Battery
Recommendation:
Check to make sure the battery activation pull
tab has been completely removed, battery polarity is correct and the
battery terminals are making contact with the smoke alarm contacts
in the battery drawer. If chirp continues, replace the 9V battery (see
User's Manual for recommended battery types).
3 Beeps,
2 second pause,
Repeat
3 Beeps,
2 second pause,
Repeat
Stays On
Condition:
Alarm has sensed smoke.
Recommendation:
Silence Feature is activated by pressing and
releasing the Test/Silence button on the initiating alarm while in alarm
condition. Silence mode will last for approx 10 minutes with the red
LED blinking once approx. every 10 seconds.
Blinks On
approx every
2 seconds
Silent
(alarmed
previously)
CONDITION / RECOMMENDATION
HORN
RED LED
GREEN LED
Blinks On once
approx every
40-45 seconds
(normal operation
mode) or Blinks on
once approx every
10 seconds
(silence mode)
Blinks On once
approx every
40-45 seconds
3 Beeps approx
every 40 seconds
after LED flashes
Stays On
Condition:
Trouble/Service Alarm.
Recommendation:
Replace Alarm.
AUDIBLE & VISUAL SIGNALS
Blinks On approx. 3
times approx every
35 seconds
1 Beep
approx every
35 seconds
Condition:
Product End-of-Service Life alarm.
Recommendation:
Replace alarm immediately. The product end-
of-service life alarm can be temporarily silenced for a 24 hour period
for up to 25 days. After 25 days, the warning cannot be silenced. The
alarm should be replaced immediately.
Stays On
