background image

 10. Care of Your Fan and Troubleshooting 

Care of Your Fan

Here  are  some  suggestions  to  help  you  

maintain your fan.

1.  Because  of  the  fan’s  natural  movement, 

some  connections  may  become  loose. 

Check the support connections, brackets, 

and blade attachments twice a year. Make 

sure they are secure. (It is not necessary to 

remove fan from ceiling.)

2.  Clean your fan periodically to help maintain 

its new appearance over the years. Do not 

use water when cleaning, this could damage 

the  motor,  or  the  wood  or  possibly  cause 

an  electrical  shock.  Use  only  a  soft  brush 

or lint-free cloth to avoid scratching the 

finish. The plating is sealed with a lacquer 

to minimize discoloration or tarnishing.  

Warning - Make sure the power is off  

before cleaning your fan.

3.  You can apply a light coat of furniture polish 

to the wood for additional protection and 

enhanced  beauty.  Cover  small  scratches 

with a light application of shoe polish.

4.  There is no need to oil your fan.  

The  motor  has  permanently  lubricated 

sealed ball bearings.

MAKE  SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX 

BEFORE YOU ATTEMPT TO MAKE ANY REPAIRS. REFER TO THE SECTION, 

“MAKING ELECTRICAL CONNECTIONS.”

Fan will not start
 

Fan sounds noisy

1.  Check main and branch circuit fuses or breakers

2.  Check line wire connections to the fan and switch wire connections in 

the switch housing. CAUTION: Make sure main power is off.

1.  Make sure all motor housing screws are snug.

2.  Make sure the screws that attach the fan blade bracket to the motor hub 

are tight.

3.  Make sure wire nut connections are not rattling against each other or 

the interior wall of the switch housing. 

CAUTION: Make sure power is off.

4.  Allow a 24-hour “breaking in” period. Most noises associated with a 

new fan disappear during this time.

5.  Make sure the canopy is a short distance from the ceiling. 

It should not touch the ceiling.

6.  Make sure your electrical box is secure and rubber isolator pads were 

used between the mounting bracket and electrical box.

Troubleshooting

Problem Solution

Summary of Contents for UHP9220














Reviews: