16 port Gigabit Ethernet switch Upvel US-16G
Package contents
•
US-16G switch
•
Power cable
•
Rack mounting kit
•
Installation guide, warranty cert.
Requirements
•
A computer with a network adapter installed
•
Cat.5, Cat.5e or Cat.6 network cable
•
Make sure that the power outlet is close enough (not further than the length of the
power cable)
•
Make sure the power cable is not damaged
•
Make sure that there is proper heat dissipation from the switch and adequate
ventilation around the switch
•
Do not place heavy objects on the switch
Specifications
Standards
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3x Flow Control
IEEE 802.3ab 1000BASE-T
IEEE 802.3az Green Ethernet
Cables
Ethernet: cat. 3, 4 or 5, up to 100 m.
Fast/Gigabit Ethernet: cat. 5, 5e or 6, up
to 100 m.
Data Rates
(half-duplex / duplex
mode)
Ethernet: 10 / 20 Mbps
Fast Ethernet: 100 / 200 Mbps
Gigabit Ethernet: 1 / 2 Gbps
Switching
Capacity
32 Gbps
Forwarding Rate
10BASE-T: 14880pps/port
100BASE-TX: 148800pps/ port
1000BASE-T: 1488000pps/port
Protocol / Topology
CSMA/CD, Star
Interfaces
RJ-45 Auto-Negotiation (Auto-MDI/ MDIX)
Switching table
8000 entries for each device connected
Jumbo frames
Up to 9 KB
Power Consumption
No more than 10 W
Status LEDs
Power, Link/ACT
Power adapter
Internal, 100 ~ 240V; 50/60 Hz
; 1 А
Temperature
- operating: 0 ~ 40 °C
- storage: -10 ~ 70 °C
Humidity
Max. 90% (non-condensing)
Dimensions
280 x 180 x 44.3 mm
Mass
1460г
MTBF
87,600 hours (10 years)
Certification
CE, FCC, Rostest
Installing the switch
1.
Connect the power cable to the power port
of the switch, then connect the power cable
to the outlet that meets the required
standards (100 ~ 240V; 50/60 Hz; 1
А
).
2.
Connect the network interface of your
computer with any port of the switch via
network cable (UTP cat. 5, 5e or 6).
Status LEDs
PWR
Green :
Power is on
Not Illuminated :
Power is off
Link/ACT
Green (Solid):
Successful connection for the
port
Green (Blinking):
Activity is occurring
Not Illuminated :
No activity is detected
If you still encounter problems or have any questions regarding the
US-16G
please contact UPVEL Technical Support Department.
Toll Free Support Hotline:
USA/Canada:
1 (800) 457-381
UPVEL
Los Angeles, CA USA
UPVEL is registered Trademark
Designed in USA / Made in China
Troubleshooting
The status LEDs remain inactive after plugging in the power cable.
1. Make sure the connector of the power cable is connected properly and the power plug
is connected to a power outlet with the characteristics relevant to the specifications
(100 ~ 240V; 50/60 Hz; 1
А
). Make sure the power cable is undamaged.
2. Check for the electric potential in the outlet (e.g. with an electrician's screwdriver).
After connecting computers to a
switch the Internet access is
available only from one of them.
This switch is not designed to share
the Internet connection between
multiple computers with no means of
other network devices.
After connecting computers to a switch there are problems with sharing files in a
network.
1.
Check the LEDs on the Switch. Make sure the Link/ACT LED is on.
2.
Make sure your network cables are undamaged and are of 1.5 to 100 meters length.
3.
Try to disable all of your firewalls.
4.
Make sure that file sharing feature of the operating system is enabled and configured.
Please refer to documentation of support of the OS you use.
Which port is the Uplink port?
Since all the ports on the Switch are
Auto-MDIX, any of the ports can be
used as an uplink port.
