Upright X Series Service & Parts Manual Download Page 29 | Manualshive

Page: 29 / 164

background image

Page 3-1

X Series Work Platform

Se

ct

ion

3

M

AINTENANCE

3.1 I

NTRODUCTION

Reference: • Section 2 for recommended maintenance intervals.

NOTE:

For Information on the engine refer to your local engine dealer.

This section contains instructions for the maintenance of the work platform. Procedures for the oper-
ation inspection, adjustment, scheduled maintenance, and repair/removal are included.

Referring to Section 2 will aid in understanding the operation and function of the various compo-
nents and systems of the work platform, and help in diagnosing and repair of the machine.

T

ERMINOLOGY

T

ER MINA L

B

LOCKS

Located in upper and lower control boxes. Designated by TB##. (##) designates the number of the
block which is written on the terminal block. “R” (right) or “L” (left) may follow the number.

W

IRE

C

OLOR

Indicated by color/color. First color refers to insulation color and second color indicates stripe. If sec-
ond color is not given, there is no stripe.

G

ENERAL

P

ROCEDURES

C

ONTAC T

B

LOCKS

Removed by inserting a flat screwdriver into the slot at either end of the block and prying outward.
Installed by pressing into an empty slot.

S

WITCH

M

OU NT

B

A SE

Assembled to back of switch actuator. Removed by rotating the small black lever counterclockwise
and lifting off the base.

T

ER MINA L

B

LOCKS

Remove wires by inserting a small flat bladed screwdriver into square beside the wire. Install wires
by stripping ½” of insulation, inserting screwdriver in square and inserting wire. Be sure no strands
are bent backwards. Replace wires with same rating and type.

3.2 D

ATE

C

ODE

I

DENTIFICATION

ON

H

OSES

G

ATES

uses a five digit code:

Year, Month, Day

.

i.e.: 6 11 29 - means 1996, month 11 (November), day 29.

P

ARKER

uses a ten digit code:

Plant, Year, Month, Day.

i.e.: XXXX 6 11 29 - means Plant XXXX, 1996, month 11 (November), day 29.

D

A YCO

stamps month, day and year on each hose.

W A R N I N G

!

!

Be sure to read, understand and follow all information in the Operation
Section of this manual before attempting to operate or perform service on
any work platform.

060571-005

«
...
27
28
29
30
31
...
»

Summary of Contents for X Series





































































































































































Reviews:

No comments

Related manuals for X Series

Brand: Keithley Pages: 97

Brand: Happ Pages: 52

Brand: Badger Meter Pages: 48

Brand: HALDER Pages: 2

Brand: Parkside Pages: 94

Brand: R-Tech Pages: 57

EAGLE GRIP EG4MDC2-F

Brand: Easy Lift Equipment Pages: 17

Brand: Telwin Pages: 88

Brand: Quickie Pages: 108

Brand: Contec Pages: 7

Caddy Tig 1500i VRD

Brand: ESAB Pages: 28

Hardon mini R1271C

Brand: Caen RFID Pages: 39

Brand: Euroscreen Pages: 39

WEB’LOG RESIDENTIAL

Brand: Meteo Control Pages: 4

Brand: Balluff Pages: 4

Brand: VIA Technologies Pages: 2

Brand: National Instruments Pages: 77

Brand: Ravaglioli Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands