background image

© UPLIFT Desk

 • 1-800-349-3839 • [email protected] • www.upliftdesk.com

9

8.

TECHNICAL SPECIFICATIONS

 

Height Range

 

24.5” - 50.25” (without desktop)

 

Base Width

 

42.125” min - 74.75” max

 

Travel Speed

 

1.5” per second (varies, slowest w/ maximum load)

 

Weight Capacity

  353 lbs.

 

Duty Cycle

 

10%, Max. 2 mins on, 18 mins off
4 Memory presets
Soft Start/Stop
Adjustable leveling studs

Copyright Notice: 

This guide is a component of the UPLIFT Desk™. This guide is a part of the scope of delivery, even if the item is resold. This guide is also available on 

the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent 
of UPLIFT Desk.
These instructions are subject to United States copyright law.

©

Keep children away from electric height-adjustable desks, control units, 
and keypads. There is a risk of injury and electric shock.

If casters are not installed, use a two-person lift and lift the desk so that it can be moved without 
dragging. Dragging the desk may cause the frame and screws to pull loose from the desktop.

This product is designed with a duty cycle of 10%. 
(2 min. on, 18 min. off)

In the event of a power outage or if the power cord is unplugged, 
a manual reset may be necessary. (see Reset Instructions above)

Do not open any of the components: lifting columns, control box, 
or keypad. There is a danger of electric shock.

Keep all electrical components away from liquids.

i

i

!

!

!
!

Summary of Contents for 2-Leg Height Adjustable Standing Desk










Reviews: