UPLIFT 2-Leg Height Adjustable Standing Desk Directions For Assembly And Use Download Page 1 | Manualshive

Page: 1 / 9

background image

UPLIFT 2-Leg Height Adjustable Standing Desk

- For use with UPLIFT Eco and Eco Curve desktops -

DIRECTIONS FOR ASSEMBLY AND USE

Your UPLIFT Eco desktop is thinner than most desktops. Before attaching accessories,
check the screw length against the thickness of the desktop to ensure that the screw is
not too long and won’t break through to the top of your desktop.

If you have an UPLIFT Eco Curve desktop (where the edge tapers downat the center cut),
it is best to not attach anything underneath that portion of the desktop as the fasteners
used will assuredly be too long and will break through to the topside of your desktop.

Please Note

®

SAVE THESE INSTRUCTIONS:

Any user or installer of desk base must study this manual carefully. If this desk is sold,

please provide the manual to the buyer, installers, or support personnel operating the product.

TABLE OF CONTENTS

PAGE

1

Safety and Warnings

2

2 Usage

2

3

Parts List

3

4

Assembly Instructions

4

5

Desk Placement

7

6 Programming

8

7 Troubleshooting

9

8

Technical Specifications

9

90.014.01.0158v.B

FRM200/R02

© UPLIFT Desk

• 1-800-349-3839 • [email protected] • www.upliftdesk.com

1
2
3
...
»

Summary of Contents for 2-Leg Height Adjustable Standing Desk










Reviews:

No comments

Related manuals for 2-Leg Height Adjustable Standing Desk

Brand: Magres Baldai Pages: 2

Brand: BACKHOME Pages: 12

Bronston 12341B

Brand: Abbyson Pages: 8

Brand: Walker Edison Pages: 15

Brand: Walker Edison Pages: 15

Brand: Nucraft Pages: 13

Brand: Allen + Roth Pages: 10

Brand: Quoizel Pages: 2

Brand: Germania Pages: 12

Brand: Trasman Pages: 20

Brand: Forte Pages: 20

Brand: GFW Pages: 13

Lapalma FORK P120

Brand: Zenith Pages: 8

The Coffee Table

Brand: neighbor Pages: 8

Brand: KayserBetten Pages: 24

Power Ease Recliner

Brand: LAZBOY Pages: 28

COMBIFLEX 410146.11

Brand: BOPITA Pages: 19

Brand: BCP Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands