manualshive.com logo in svg

Upland 207P, Installation And Operation Manual, Page: 16 / 33

Share
Download
Upland 207P Installation And Operation Manual Download Page 16

operation the trapdoor is held open by an electro-
magnet.)  The sensor should then indicate OK.  Once
confirmed, allow the trapdoor to close.

 

Lift lever to open.

  (Located on back of hopper)

  If you have any problems at    
this point contact us.

With all of the wiring and sensors checked out, you
are ready to start a fire.  Press the MENU button until
you see the following screen.

Answer YES and the controller will print step by
step instructions for lighting a fire.

Double check that there are

 

no foreign objects in the 

hopper.  Pour about 1/4 bag

 

into the hopper

.

Allow the auger to start to feed pellets into the burn pot. 

Then pour several cups of pellets in the burnpot so
that pellets fill it to the brim.

  Adjust the nozzle to point

downwand and centered over the burn pot.

A

dd a small amount of gel lighter (prefer

r

ed) or

other approved pellet igniter.  Do not overdo it - add
about on table spoon maximum.

Summary of Contents for 207P


































Reviews:

No comments