uniview technologies IPC672LRa Quick Manual Download Page 11

 

10 

 

Uniview reserves the right to change any information in this manual without any prior notice 
or indication. Due to such reasons as product version upgrade or regulatory requirement of 
relevant regions, this manual will be periodically updated. 

Disclaimer of Liability 

 

To the extent allowed by applicable law, in no event will Uniview be liable for any special, 
incidental, indirect, consequential damages, nor for any loss of profits, data, and documents. 

 

The  product  described  in  this  manual  is  provided  on  an  "as  is"  basis.  Unless  required  by 
applicable law, this manual is only for informational purpose, and all statements, information, 
and recommendations in this manual are presented without warranty of any kind, expressed 
or implied, including, but not limited to, merchantability, satisfaction with quality, fitness for 
a particular purpose, and noninfringement.   

 

Users must assume total responsibility and all risks for connecting the product to the Internet, 
including,  but  not  limited  to,  network  attack,  hacking,  and  virus.  Uniview  strongly 
recommends that users take all necessary measures to enhance the protection of network, 
device, data and personal information. Uniview disclaims any liability related thereto but will 
readily provide necessary security related support.  

 

To the extent not prohibited by applicable law, in no event will Uniview and its employees, 
licensors, subsidiary, affiliates be liable for results arising out of using or inability to use the 
product  or  service,  including,  not  limited  to,  loss  of  profits  and  any  other  commercial 
damages  or  losses,  loss  of  data,  procurement  of  substitute  goods  or  services;  property 
damage, personal injury, business interruption, loss of business information, or any special, 
direct, indirect, incidental, consequential, pecuniary, coverage, exemplary, subsidiary losses, 
however  caused  and  on  any  theory  of  liability,  whether  in  contract,  strict  liability  or  tort  
(including negligence or otherwise) in any way out of the use of the product, even if Uniview 
has  been  advised  of  the  possibility  of  such  damages  (other  than  as  may  be  required  by 
applicable law in cases involving personal injury, incidental or subsidiary damage). 

 

To the extent allowed by applicable law, in no event shall Uniview’s total liability to you for 
all  damages  for  the  product  described  in  this  manual  (other  than  as  may  be  required  by 
applicable law in cases involving personal injury) exceed the amount of money that you have 
paid for the product.  

Network Security 

Please take all necessary measures to enhance network security for your device. 

The following are necessary measures for the network security of your device: 

 

Change  default  password  and  set  strong  password

:  You  are  strongly  recommended  to 

change the default password after your first login and set a strong password of at least nine 
characters including all three elements: digits, letters and special characters. 

 

Keep firmware up to date

: It is recommended that your device is always upgraded to the 

latest version for the latest functions and better security. Visit Uniview's official website or 
contact your local dealer for the latest firmware. 

The following are recommendations for enhancing network security of your device: 

 

Change password regularly

: Change your device password on a regular basis and keep the 

password safe. Make sure only the authorized user can log in to the device. 

Summary of Contents for IPC672LRa















Reviews: