Universal Security Instruments Sensing Plus AMIC3511S Instructions Manual Download Page 14

Page: 14 / 15

Page 14

RESET INSTRUCTIONS: Press the Test/Silence button for 10-15 seconds and then release. This will clear the alarm origination. Be sure to RESET

alarms after each alarm event. QUICK FIND

Alarm Origination/Location Feature: The QUICK FIND

feature will allow you to immediately locate the

originating alarm (the alarm that triggered the other alarms), once the alarms have stopped sounding.

1. Press and release the Test/Silence button on alarm. After releasing the button, the test sequence on this alarm will begin, and

last approximately 5-20 seconds. If it is not the originating alarm, continue to each alarm until the originating alarm is located.

2. Once this test sequence ends, the originating alarm continues to sound for approximately 60 seconds, which provides ample time to

locate the originating alarm.

3. Remember to reset the originating alarm in order to clear the QUICK FIND

and return the system to normal operation.

NOTE: If you have any additional questions about the operation of this product, please contact our Customer Service Department

at 800-390-4321, and we will gladly assist you.

THIS PRODUCT IS LISTED TO UL STANDARD FOR SAFETY, UL 217 8TH EDITION and UL 2034 4th Edition.

Quick Reference Guide Model AMIC3511S (continued from previous page)

Summary of Contents for Sensing Plus AMIC3511S















