D700C120UVT
‐
Vx
For
the
“N”
and
“F”
versions,
Tc location
is
on
the
bottom
of
the
case.
For
the
“J”
version
with
the
leads
exiting
out
the
bottom,
the
screw
on
the
side
of
the
case
is
oriented
to
the
right
and
the
Tc is
Tc Location
Conditions
of
Acceptability
–
1.
These
products
are
for
use
only
in
(or
with)
complete
end
product
i
h
h
bili
f h
bi
i
i d
i
d b
located
on
the
side
with
the
label.
‐
VJ
Case
‐
VF
Case
1 45”
2.72”
1.
2.
.
3.
Product / product installation into end product is subject to any additional applicable requirement(s) of all
equipment
where
the
acceptability
of
the
combination
is
determined
by
CSA
International
or
others
having
jurisdiction.
2.
The
product
shall
be
installed
in
compliance
with
the
enclosure,
mounting,
mounting
surface,
strain
relief,
pushback
relief,
spacing,
segregation,
and
all
other
applicable
requirements
of
the
End
Product
in
which
it
is
employed. Suitability
shall
be
determined
during
End
Product
Certification
Evaluation.
1.45
3.
Product
/
product
installation
into
end
product
is
subject
to
any
additional
applicable
requirement(s)
of
all
applicable
end
product
standard(s). These
requirements
shall
be
verified
during
end
product
evaluation.
4.
These
Drivers
were
evaluated
for
use
in
an
elevated
ambient
not
exceeding
41°C
and
the
maximum
case
temperature
at
(Tc)
location
should
not
exceed
75°C
when
the
driver
is
installed
in
the
end
‐
use
application.
5.
These
products
are
suitable
for
use
in
wet
locations
only
when
the
optional
CSA/UR
(cUS,
INT)
water
resistant
wiring
is
incorporated
in
the
products.
Otherwise
the
products
are
suitable
for
damp
locations
only.
6.
The
output
from
the
0
‐
10
Vdc dimming
interface
(violet
and
gray
leads)
was
tested
and
found
compliant
with
the
Class
2
limits
in
accordance
with
UL
1310
and
CSA
C22.2
No.
223.
FCC
Statement:
This
device
complies
with
part
15
of
the
FCC
Rules.
Operation
is
subject
to
the
following two conditions: (1) This device may not cause harmful interference and (2) this device
7.
The
Mechanical
Strength
test
on
enclosures
was
performed
in
accordance
with
UL
8750
and
CSA
C22.2
No.
250
‐
13.12.
The
suitability
of
the
enclosure
of
the
unit
with
regards
to
the
outcome
of
this
test
shall
be
determined
in
the
end
‐
product
evaluation.
8.
All
parts
of
these
models
are
fully
submerged
in
potting
compound
in
accordance
with
sub
‐
clause
41.1
(c)
of
UL
844
Warranty:
Universal
Lighting
Technologies
warrants
to
the
purchaser
that
each
power
supply
will
be
free
from
defects
in
material
or
workmanship
for
a
period
of
5
years
from
the
date
of
manufacture
when
properly
installed
per
instructions
and
under
normal
operating
conditions
of
use.
Call
1
‐
800
‐
225
‐
5278
for
technical
assistance.
following
two
conditions:
(1)
This
device
may
not
cause
harmful
interference,
and
(2)
this
device
must
accept
any
interference
received,
including
interference
that
may
cause
undesired
operation.
Page
3
of
3
www.unvlt.com
February
6,
2014
Application
and
operation
performance
specification
information
subject
to
change
without
notification.
