Universal Innovations Sahara X450 Manual Download Page 1

X4

50 Barbecue

Photograph is not to scale. Specification

subject to change without prior notice.

• For outdoor use only.

• Read instructions before using the appliance. Failure to follow instructions could result in

death, serious bodily injury, and/or property loss.

• Warning: accessible parts may be very hot. Keep young children away.

• Do not move the appliance during use.

• Turn off the gas supply at the gas bottle after use.

• Any modification of the appliance, misuse, or failure to follow the instructions may be

dangerous and will invalidate your warranty. This does not affect your statutory rights.

• Retain these instructions for future reference.

• Leak test your barbecue annually. Check the hose connections are tight and leak test each 

time you reconnect the gas bottle

WARNING

FOR YOUR SAFETY 

 

FOR YOUR SAFETY

IF YOU SMELL GAS:
1. Shut off gas to the appliance.  

 

1. Do not store or use petrol or other flammable vapours or 

 

2. Extinguish any open flame.   

 

    liquids in the vicinity of this or any other appliance.

3. Open barbecue lid or hood.   

 

2. A gas bottle not connected for use shall not be stored in the

4. If odour continues, discontinue use and   

    vicinity of this or any other appliance.

contact your local dealer.

Universal Innovations

Manufactured by

www.uigroup.ie

Summary of Contents for Sahara X450























Reviews: