background image

Unitronics  

1

Vision™ OPLC™ 

V350-35-B1  
Installation Guide

 

The Unitronics V350-35-B1 offers the following features: 
I/O configurations can be added via Expansion Modules.  
Available by separate order: Ethernet, additional RS232/RS485, CANbus. 

General Description 

V350 OPLCs are micro-OPLCs, rugged programmable logic controllers that comprise:  

Built-in operating panel containing a 3.5” Color Touchscreen and programmable function keys 

Communications 

1 built-in serial port: RS232/RS485  
Optional—the user may order and 
install one or both of the following 
modules:  
- RS232/RS485/Ethernet  
- CANbus 
Communication Function Blocks 
include: SMS, GPRS, MODBUS 
serial/IP. Protocol FB enables PLC to 
communicate with almost any external 
device, via serial or Ethernet 
communications 

I/O Options 

V350 supports digital, high-speed, analog, 
weight and temperature measurement 
I/Os via: 

I/O Expansion Modules
Local or remote I/Os may be 
added via expansion port or 
CANbus.  

Information Mode 

This mode enables you to: 

View & Edit operand values, COM port settings, RTC and screen 
contrast/brightness settings 
Calibrate the touchscreen 
Stop, initialize, and reset the PLC 

To enter Information Mode, press the <i> button for several seconds. 

Programming 
Software,  
& Utilities 

The Unitronics Setup CD contains VisiLogic software and other utilities 

VisiLogic
Easily configure hardware and write both HMI and Ladder control 
applications; the Function Block library simplifies complex tasks 
such as PID. Write your application, and then download it to the 
controller via the programming cable included in the kit. 
Utilities
Includes UniOPC server, Remote Access for remote programming 
and diagnostics, and DataXport for run-time data logging. 

To learn how to use and program the controller, as well as use utilities such 
as Remote Access, refer to the VisiLogic Help system. 

Removable 
Memory Storage 

Micro SD card: store datalogs, Alarms, Trends, Data Tables; export to Excel; 
backup Ladder, HMI & OS and use this data to ‘clone’ PLCs. 
For more data, refer to the 

SD

 topics in the VisiLogic Help system. 

Data Tables 

Data tables enable you to set recipe parameters and create datalogs. 

Summary of Contents for Vision OPLC V350-35-B1









Reviews: