background image

 

Unitronics 

 

 

Vision

PLC+HMI 

Installation Guide 

V130-33-TA24/V130-J-TA24 
V350-35-TA24/V350-J-TA24 
V350-S-TA24/V350JS-TA24 
V430-J-TA24 

 

12 Digital Inputs, including 2 Analog,  
2 PT100/TC ,1 HSC/Shaft-encoder input 

 

 

10 Transistor Outputs, 2 Analog Outputs 

 

 

 

General Description 

 

All of the controllers covered in this guide are micro-PLC+HMIs, rugged programmable logic controllers 
that comprise built-in operating panels and on-board I/Os. 

 

Item 

V130-TA24 

V130-J-TA24 

V350-TA24/V350-J-TA24 

V350-S-TA24/V350-JS-TA24 

   V430-J-TA24 

On-board I/O 

Model Dependent 

Screen 

2.4" 

3.5" Color Touch 

4.3" Color Touch 

Keypad 

Yes 

None 

Function Keys 

None 

Yes 

Com Port, Built-in 

 

 

RS232/485 

Yes 

Yes 

Yes* 

Yes* 

Yes* 

USB device,  

mini-B 

None 

None 

Yes* 

Yes* 

Yes* 

Com Ports, separate 
order, user-installed  

The user may install a CANbus port (V100-17-CAN), and 

one

 of the following: 

 

RS232/RS485 port (V100-17-RS4/V100-17-RS4X)  

 

Ethernet (V100-17-ET2)

 

 

 

Profibus Slave (V100-17-PB1) 

* V430J/V350/V350J/V350S/V350JS comprises both RS232/485 and USB ports; note that only 

one

 channel may be 

used at a time. 

 

Standard Kit Contents 

 

Item 

V130-TA24 

V130-J-TA24 

V350-TA24/V350-J-TA24 

V350-S-TA24/V350-JS-TA24 

V430-J-TA24 

 

Controller 

Yes 

Terminal Blocks 

Yes 

Battery (installed) 

Yes 

Slides  
(2 sets of key labels) 

None 

Yes 

None 

Mounting Brackets 

Yes (2 parts) 

Yes (4 parts) 

Rubber Seal 

Yes 

Programming cable 
+ RS232 adapter 

Yes 

None 

USB  
programming cable 

None

 

Yes

 

 

Summary of Contents for Vision OPLC V130-33-TA24













Reviews: