background image

Unitronics  

Vision™ OPLC™  

V130-33-T38 Installation Guide 
22 pnp/npn Digital, including 2 Analog, 2 HSC/Shaft-
encoder Inputs, 16 pnp Outputs 

This guide provides basic information for Unitronics’ controller model V130-33-T38.   

General Description 

V130 OPLCs are micro-OPLCs, rugged programmable logic controllers that comprise:  

On-board I/O configuration 
Built-in operating panel containing an LCD and a keypad  

Communications 

1 built-in serial port: RS232/RS485  
Optional: the user may order and install 
one or both of the following modules:  
- RS232/RS485/Ethernet  
- CANbus  
Communication Function Blocks include: 
SMS, GPRS, MODBUS serial/IP. Protocol 
FB enables PLC to communicate with 
almost any external device, via serial or 
Ethernet communications 

I/O Options 

V130 supports digital, high-speed, analog, 
and temperature measurement I/Os via: 

On-board I/O configuration
Model-dependent 
I/O Expansion Modules
Via adaptor, use up to 8 I/O Expansion 
Modules, add up to 128 additional I/Os 

Information Mode 

This mode enables you to: 

View & Edit operand values, COM port settings, RTC and screen 
contrast/brightness settings 
Stop, initialize, and reset the PLC 

To enter Information Mode, press the <i> button for several seconds. 

Programming 
Software,  
& Utilities 

The Unitronics Setup CD contains VisiLogic software and other utilities 

VisiLogic
Easily configure hardware and write both HMI and Ladder control 
applications; the Function Block library simplifies complex tasks 
such as PID. Write your application, and then download it to the 
controller via the programming cable included in the kit. 
Utilities
Includes UniOPC server, Remote Access for remote programming 
and diagnostics, and DataXport for run-time data logging. 

To learn how to use and program the controller, as well as use utilities such 
as Remote Access, refer to the VisiLogic Help system. 

Data Tables 

120K dynamic data (recipe parameters, datalogs, etc.),  
192K fixed data (read-only data, ingredient names, etc) 

Additional product documentation is in the Technical Library, located at 

www.unitronics.com

, and on 

the Unitronics’ Setup CD. 
Technical support is available at the site, and from [email protected]

 

Summary of Contents for Vision OPLC V130-33-T38











Reviews: