background image

E X - A2 X      

I / O   E x p a n s i o n   M o d u l e   Ad a p t e r ,   I s o l a t e d  

1 2 / 0 9

Notes:

1. 

Example: 2 I/O-DI8-TO8 units consume a maximum of 140mA  of the 5VDC supplied by the EX-A2X. 

Addressing I/Os on Expansion Modules

 

Inputs and outputs located on I/O expansion modules that are connected to an OPLC are assigned 
addresses that comprise a letter and a number.  The letter indicates whether the I/O is an input (I) or an 
output (O).  The number indicates the I/O’s location in the system.  This number relates to both the position 
of the expansion module in the system, and to the position of the I/O on that module. 

Expansion modules are numbered from 0-7 as shown in the figure below. 

 

0

1

2

3

4

5

6

7

Expansion module
identification number

Adapter

The formula below is used to assign addresses for I/O modules used in conjunction with the OPLC. 

X is the number representing a specific module’s location (0-7).  Y is the number of the input or output on 
that specific module (0-15).   

The number that represents the I/O’s location is equal to: 

32 + x  16 + y 

Examples 

Input #3, located on expansion module #2 in the system, will be addressed as I 67, 
67 = 32 + 2  16 + 3 

Output #4, located on expansion module #3 in the system, will be addressed as O 84,  
84 = 32 + 3  16 + 4. 

 

EX90-DI8-RO8 is a stand-alone I/O module.  Even if it is the only module in the configuration, the EX90-DI8-
RO8 is always assigned the number 7. 

Its I/Os are addressed accordingly. 

 

Example 

Input #5, located on an EX90-DI8-RO8 connected to an OPLC will be addressed  
as I 149, 149 = 32 + 7  16 + 5 

 

Unitronics_EX-A2X_IO_Expansion_en_0511.pdf

Samara

tel. +7 846 273 95 85
[email protected]

Yekaterinburg

tel. +7 343 376 5393
[email protected]

St. Petersburg

tel. +7 812 327 3752
[email protected]

Moscow

tel. +7 495 641 1616
[email protected]

Helsinki

tel. +358 9 540 4940
automation@klinkmann.fi

Vilnius

tel. +370 5 215 1646
[email protected]

Riga

tel. +371 6738 1617
[email protected]

Мinsk

tel. +375 17 200 0876
[email protected]

Tallinn

tel. +372 668 4500
[email protected]

Кiev

tel. +38 044 495 33 40
[email protected]

www.klinkmann.com

Summary of Contents for EX-A2X







Reviews: