manualshive.com logo in svg

Unitech MS842DPM, User Manual, Page: 69 / 107

Share
Download
Unitech MS842DPM User Manual Download Page 69

 

 

Bookland EAN 

Enable/Disable Bookland EAN 

To enable or disable Bookland EAN, scan the appropriate bar code below. 

 

 

 

 

Note: 

If Bookland EAN is enabled, select a 

Bookland ISBN Format

. Also select either Decode 

UPC/EAN Supplementals, Autodiscriminate UPC/EAN Supplementals, or Enable 978/979 
Supplemental Mode in 

Decode UPC/EAN/JAN Supplementals

. 

 

Bookland ISBN Format 

If Bookland EAN is enabled, select one of the following formats for Bookland data: 

 

Bookland ISBN-10 

- The decoder reports Bookland data starting with 978 in 

traditional 10-digit format with the special Bookland check digit for 
backward-compatibility. Data starting with 979 is not considered Bookland in this 
mode. 

 

Bookland ISBN-13 

- The decoder reports Bookland data (starting with either 

978 or 979) as EAN-13 in 13-digit format to meet the 2007 ISBN-13 protocol. 

 

 

 

 

 

Decode UPC/EAN/JAN Supplementals 

 

 

 

 

 

 

 

49

 

Copyright 2013 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd. 

Summary of Contents for MS842DPM












































































































Reviews:

No comments