Unitech MS340BT User Manual Download Page 25

Page: 25 / 75

© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd

1.6 LED Indicator / Beeper Sequence

￭

Scanner LED Status

Action/Status

LED

for

Barcode

reading

Communication

Beep

Tone

Good read and transmitted

Green light blinks once One beep

Good read and save on

memory (BT disconnect)

Green light blinks once One beep

Good Read but Transmit Fail

Green light blinks twice Two beeps

Battery fully charged

Solid green light

No action

Memory full

Red light blinks twice

Two beeps

Low Battery warning

Red light blinks once

every 20 seconds

One beep

In charging

Solid red light

No action

BT disconnect

Blue light blinks twice

(continuously)

No action

BT disconnect

before sleep

No action

Low beep

BT connected

Blue light blinks once

every two seconds

High beep

Setting ok

Green light blinks once

No action

Start charging

Solid red light

No action

Battery changed

Blue light blinks once

then green light blinks

twice

No action

Summary of Contents for MS340BT



































































Search results

Summary of Contents for MS340BT

Reviews:

Brands by name

Popular brands

Unitech MS340BT, User Manual

Search results

Summary of Contents for MS340BT

Reviews:

Brands by name

Popular brands