Unipulse TM700 Operation Manual Download Page 56

Page: 56 / 91

SETTING OF FUNCTIONS

Chapter

■

Trigger setting screen

The triggering point for plotting can be specified with a cursor.
The cursor operation is same as for wave check.

X-axis

Y-axis

Setting using a numerical value as a pre-trigger value is also possible.

≪

Setting value

≫

0 to 50 [%]

How to set

■

Hold point plotting

By using the hold function and the graph plotting function together, the held point (red) can be
plotted.

Hold point:

The hold point is displayed by a red point.
The latest hold point out of 2000 points is displayed.

Detection section display:

A cobalt line indicating the detection section is displayed at the
bottom of the X-axis.

Hold point alarm:

Flashes when only the hold value is renewed without the graph
plotting being renewed, and when the value differs from the
hold point on the graph.

SET.

Graph Setting

Page 1

→

Meas. Setting

→

- There will be no hold point within the display area before triggering.
- Plotting may not start promptly due to time needed to prepare data before

triggering immediately after power on or when X-axis scale setting or trigger
setting is changed.

Point

Hold point alarm

Hold point

Detection section display

Summary of Contents for TM700




























































































Search results

Summary of Contents for TM700

Reviews:

Related manuals for TM700

Brands by name

Popular brands

Unipulse TM700, Operation Manual

Search results

Summary of Contents for TM700

Reviews:

Related manuals for TM700

Brands by name

Popular brands