Unipulse M525B Operation Manual Download Page 46

Page: 46 / 85

FOR GREATER USE OF THE PRINTER

FOR GREATER USE OF THE PRINTER

Chapter

Select whether or not to print an error when the weight value sent from the SI/F (Ach, Bch) is
unstable or negative in addition to its abnormality (OVER, OFL, LOAD, or ZALM).

Name of setting

26: Data Check ON/OFF

Selection item

0. OFF (initial value)
1. ON

Reference

If the setting is ON, an error (R) is printed when the weight value is unstable or
negative.

Caution

- Stable data is not checked during printing of weight values from BCI and

RS-232C irrespective of whether the setting is ON or OFF.
If the setting is ON, an error (R) is printed when the weight value is negative
or OVER.

- ON only be set for corresponds to the Measurement Law of Japan.

Please set it to ON only when it is connected with indicator that is
corresponding to Measurement Law and it is used with the indicator.

26: Data Check ON/OFF

Summary of Contents for M525B






















































































Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands

Unipulse M525B, Operation Manual

Search results

Summary of Contents for M525B

Reviews:

Related manuals for M525B

Brands by name

Popular brands