Unipulse M525B Operation Manual Download Page 35 | Manualshive

Page: 35 / 85

background image

26

4

　

FOR GREATER USE OF THE PRINTER

26

FOR GREATER USE OF THE PRINTER

Chapter

4

Printing can be automatically produced by sending a print command from the SI/F or RS-232C
interface to the M252B. Select whether this Automatic Print is ON or OFF.

Details of settings

ON

Printing is produced when a print command is sent from the SI/F or RS-232C interface.
For the print commands from the SI/F and RS-232C interface, see the instruction
manual of each indicator and "5-3.RS-232C Interface (Option)" on page 41.

OFF

Printing is not produced with a print command from the SI/F or RS-232C interface.

Select whether or not to print at fixed intervals.

Details of settings

ON

Print is automatically produced at intervals of seconds set under [10: Interval
Seconds] (See below). Printing is not produced with a print command from the SI/F
or RS-232C interface.

OFF

Interval Print is not performed.

Name of setting

08: Automatic Print ON/OFF

Selection item

0. OFF
1. ON (initial value)

Caution

- Printing is always produced in the following conditions irrespective of

whether Automatic Print is ON or OFF.

- When the

(PRINT) key is pressed.

- When the PRINT terminal and COM terminal to the rear panel are short-

circuited.

- Since an automatic print command cannot be given from the BCD input, it is

necessary to give a print command on the printer for printing print data from
the BCD input.

Name of setting

09: Interval Print ON/OFF

Selection item

0. OFF (initial value)
1. ON

Caution

Keys other than

(STOP) (to stop Interval Print) and

(ENT) cannot

be used during Interval Print.

08: Automatic Print ON/OFF

・

For the print command from the SI/F, see the instruction manual of each
connection indicator.

・

For the print command from the RS-232C interface, see "5-3.RS-232C
Interface (Option)" on page 41.

Point

09: Interval Print ON/OFF

«
...
33
34
35
36
37
...
»

Summary of Contents for M525B






















































































Reviews:

No comments

Related manuals for M525B

Brand: EBS Pages: 4

Brand: NCR Pages: 38

Brand: MakerBot Pages: 48

Brand: Pantum Pages: 94

Brand: WANHAO Pages: 24

Brand: Canon Pages: 2

Brand: Star Pages: 82

Brand: Phoenix Contact Pages: 52

DocuCentre-VI C2264

Brand: Fuji Xerox Pages: 129

Brand: TierTime Pages: 35

Brand: Riso Pages: 66

GADOSO REVOLUTION 2

Brand: WANHAO Pages: 51

Brand: IOGear Pages: 44

Brand: Airlink101 Pages: 36

Brand: Xiamen Sojet Electronics Pages: 37

Brand: ZKTeco Pages: 38

Brand: Canon Pages: 343

Brand: Canon Pages: 380

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands