background image

3.CONNECTION

9

3. CONNECTION

Precautions about connection to the signal input/output terminal block are given

below.The precautions described here are important for safety.

Please properly understand the descriptions before connection.

WARNING

• Do not connect a commercial power source directly to the signal input/output terminals.

• Connect to the signal input/output terminals with no power applied because it may

cause an electric shock.

• For connection to the signal input/output terminals, check the signal names and pin

assignment numbers, and then carry out wiring properly.

• The overvoltage applied to the signal input/output terminals should not exceed the value

defined in category II.

• After wiring, be sure to mount the attached terminal block cover. Otherwise, it may

cause an electric shock.

• Before applying power, carefully check the wiring, etc.

• Do not touch any signal input/output terminal while applying power. Doing so may cause

electric shocks or malfunctions.

CAUTION

• Tighten the terminal screws at the specified torque.

 If they are loose, shorts, fire or malfunctions may occur.
Tightening torque: 0.2 to 0.6N•m

• Use shielded cables.

Summary of Contents for F320


































































































































Reviews: