Unipower INV2500-HS Operating Manual Download Page 7

4

INV2500-HS & INV5000-HS SERIES

OPERATING MANUAL

4.3

When operating these inverters, the chassis ground terminal must be con-
nected to safety ground to minimize electrical shock hazard and to ensure low
EMI (electromagnetic interference).

4.4

The internal voltages are at hazardous potentials.  The inverter covers should
not be removed.  There are no user-serviceable components in these units.
Removing the covers of the inverters will void the warranty.

5.0

WARRANTY

All products of UNIPOWER Telecom, a division of UNIPOWER Corporation, are warranted for
two (2) years from date of shipment against defects in material and workmanship.  This warranty
does not extend to products which have been opened, altered or repaired by persons other than
persons authorized by the manufacturer or to products which become defective due to acts of
God, negligence or the failure of customer to fully follow instructions with respect to installation,
application or maintenance.  This warranty is extended directly by the manufacturer to the buyer
and is the sole warranty applicable.  EXCEPT FOR THE FOREGOING EXPRESS WARRANTY,
THE MANUFACTURER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICU-
LAR PURPOSE.  As the sole and exclusive remedy under this warranty, the manufacturer, at its
option, may repair or replace the non-conforming product or issue credit, provided the
manufacturer’s inspection establishes the existence of a defect.  To exercise this remedy, the
buyer must contact the manufacturer’s Customer Service Department to obtain a Return Material
Authorization number and shipping instructions.  Products returned without prior authorization
will be returned to buyer.  All products returned for repair must be shipped freight prepaid to
UNIPOWER.  If the buyer fails to fully comply with the foregoing, the buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost
sales, injury to person or property or any other incidental or consequential losses) shall be
available to the buyer.

6.0

UNPACKING AND INSPECTION

6.1

This INV2500-HS or INV5000-HS was carefully tested, inspected and pack-
aged for shipment from our factory.  Upon receipt of the unit, it should be
carefully unpacked and inspected for any damage in shipment.

6.2

If there is evidence of damage, do not attempt to test the unit.  The freight
carrier should be notified immediately and a claim for the cost of the inverter
should be filed with the carrier for direct reimbursement.  Be sure to include
the model and serial number of the damaged unit in all correspondence with
the freight carrier.  Also save the shipping carton and packing material as
evidence of damage for the freight carrier’s inspection.

6.3

UNIPOWER Telecom will cooperate fully in case of any shipping damage
investigation.

Summary of Contents for INV2500-HS























Reviews: